I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
In our design, nRF9160 is powered by a LiPo battery, making VDD = 4.2V in a "fully charged" case, and VDD=5V in a "lipo is charging" case.
We would like to be able...
In trying to use a private key file to sign the application image I'm running into an issue with the PEM file. I created a PEM file using the following command:
as documented...
Hello colleagues,
Mi name is Daniel and i'm trying to develop a software application that let me calculate the PER (packet error rate) of a bluetooth transmission.
The...
Hello Team,
I am working on a project in which I want to used pdm microphone with nrf51822 xxAA and i am using keil u5.
1) So I have picked uart over BLE example from...
Hey there,
I am new to the community and I would like to looking for more than one cell. As I readed in another thread, it was possible with %NBRGRSRP a few month ago. ...
I was looking through documentation and I noticed that in OPS v0.7.1 the cold start was stated to be -144dBm. In PS v1.1 it calls out -142dBm. Can you explain why they are...
Hi!
I have BMD-350 -A-R and I want to program this by using SWD pins (SWCLK, SWDIO, GND Detect, and VTG) of Nrf52Dk . I make all the connections properly but for some reason...
Hi,
for evaluating purposes I'm trying to send quite big amount of data (100 kB) via socket interface. Sending proceeds fine until approximately 60 kB is transmitted. After...
Hi,
when powering up the nRF52840 PDK its interface MCU LED is blinking fast and the board is not recognized. I've tried to update its firmware by putting the board in bootloader...
On some android phones we have observed that if we try to scan using nRFToolbox for nRF51/ nRF52 controller advertising with UART they do not show up in the scan list. But...
Hello,
I am developing a wireless sensing device using the nRF24L01+ module and I'm planning to use a u.FL connector in my design. I can't seem to find any manufacturer...
Hello,
I am trying to test BLE with SAADC, UART function.
I am complete the ADC test and UART part.
So now, I want to SAADC with BLE and BLE with UART.
The whole connection...
Hi all,
I tried to follow this tutorial to be able to use GDB as debugger but failed right in the beginning because JLinkGDBServer could not connect. Here's the log I get...
Hi , i am using the nrf52dk and i have a switch statement that depending on the case there is a set of enum and i would like to utalised the push button to increase/decrease...
