Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi! We have a peripheral which uses an 'unconventional' SPI configuration for its data transfer. Among other things, it sends and receives data on the same SPI line, meaning...
Hi,
In our design we are using 25AA320 with nRF9E5 . It seems in some random conditions the EEPROM loses data and the application won't run until EEPROM is reprogramed...
I'm looking for Advertisement receiving code with control radio module without softdevice.
I want to make extremely low power control code for advertisement.
please help...
Hi, I am a beginner, during my internship I need to evaluate the nRF9169 DK for cellular applications.
I successfully implemented the communication over serial by using...
Hi,
Recently I degubbed issues on debug mode for an application on segger embedded studio 4.1.2. Now I see in release mode some kind of errors is happening, it works well...
Hi,
I'm using NRF_WDT and it works very good.
I would like to investigate my project failures and I want to save some data when watchdog is expired.
How can I catch...
I am newbie here. I was reading ‘Introduction to Nordic nRF5 SDK and Softdevice' dated 15 Jan 20. The softdevice naming rule establishes Sxyz
wherein z – denotes the SoC...
Hi,
We're noticing high power consumption when the 9160 is supposed to be PSM sleeping in borderline signal locations that is breaking our power consumption model, reducing...
The docs say:
Once configured, it is possible to perform cryptographic operations using the the CRYPTOCELL subsystem where KDR is selected as key input without having access...
Running nRF Connect SDK v2.1 targetting an nRF52840 DK (PCA10056)
I'm looking at the OTA DFU options for this SDK. The host side tool if i'm not mistaken is a go utility...
Hello,
I'm trying to integrate Mesh 4.0.0 into a program built with SDK 16.0.0 but I'm running into some issues including the correct files from the Mesh SDK. I followed...
Hi Sir,
In the datasheet of 52840, we know the DEC1 is 1.1V, DEC2/4/5 are 1.3V, DECUSB is 3.3V.
When measuring these pins, we may not get a precision value, like we got...
Hello,
I am developing an application to scanning a device continuously in nrf52832 chip. My concern is that when the device scan the other peripherals it consume a lot...
Hi,
Can you please give a brief idea which softdevice and SoC we should use as per our requirements.
1) The device should be able to connect to the mobile phone(mobile...
I am not able to build in release mode where as in debug mode builds. Even when option for release is chose , it builds in debug mode. I am using Segger Embedded studio 4...
