Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi,
reading through the gnss socket configuration parameters it came a question to my mind regarding the Power Save Modes.
Is the PSM configuration applied when the GPS...
Followed the example https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/spi
but getting spi received value 0xff each time
my conf file:...
Hello, I am a bit confused with the ARM Cryptocell 310 engine. As I can see this software is proprietary but in nrf5 sdk there is the cryptocell engine as external library...
Hi,
I am using nrf52810 ,softdevice 132.
I am trying to implement whitelist in ble_app_uart code (peripheral side).I take reference from HID mouse example.
Code compiled...
Hello everyone,
We're looking to develop a prototype of a very simple panic button. The device should automatically pair with iOS / Android, and establish a call to a given...
I have an example application executing on the nRF52840-DK on SDK15.0.0, see https://devzone.nordicsemi.com/f/nordic-q-a/67351/are-there-any-differences-between-sdk15-and...
When we try and stream BLE data to the nRF Connect app on an Android or IOS phone the app accepts our requested for an MTU of 244 or 160 respectively, however it does not...
Hi,
Dev setup:
Segger embedded studio - fatfs example - SD card - nrf52832
I am able to write to sd card and see data. But while reading i am failing.
Below is code...
Hi,
I am a bit confused after looking through all the SDK solutions available for NRF52 and need a piece of advice...
I am have started on the project that consists...
Can I periodically or continuously read the characteristic of peripheral after the connection?
If there is a change in the value in peripheral, then the value is received...
Hi,
i am trying to do buttonless dfu . I want to merge all hex files into one as per the document .when i enter the mergehex , i am getting mergehex command not found why...
Hi,
I'm making an new board with both nrF52840 and nRF9160. In addition to the radio ICs there will be some antenna diversity switches, chip antennas etc.
So I'd like...
Hi,
I'm using SDK 15.2 with Nrf52832,
I've implemented a custom service with read, write and notification services.
I would appreciate if you could send me an example...
Hi,
I have a problem with the NRF52840 DK rev. 2.0.1 coin cell. When powered via USB board is working properly but when powered with coin cell nothing happens.
SW08 is...
