Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi,
I'm currently trying to load my firmware into some custom nRF52832 boards. It seems that several of them have been locked up after previously working. Other boards...
Hi, we recently purchased a Nordic Thingy 52 module and were trying to program it. We used a J-link recorder and a cable for the connection between the J-link and the Thingy...
I have installed CMSIS according to this
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v14.1.0%2Fsdk_config.html
documentation. After...
Hi Team,
One of my application needs the UART driver in both Interrupt and DMA mode for more data bytes transfer. No need of timeout operation or polling mode.
Can any...
Hello Nordic;
I use SDK 17.0.2 and gls example . We know for security in pairing, considered a password which that is randomly generated in SoftDevice and sent to UART....
I am having problems loading an existing project that I successfully built and ran in the past.
I open IDE from nRF Connect > Toolchain Manager > Open IDE
The SES opens...
Hi,
Our Nordic app is doing BLE<->SPI communication.
All works fine when running in debug mode with SEGGER IDE.
Once we run without the debugger running, the SPI transmits...
Any idea why I need to send write enable twice, without reading the status in between, to get the write latch set?
It doesn't work this way, but if I change "#if 0"...
Hi,
I'm using nrf52840 on a custom board and have a sensor connected over the pins P0.9 and P0.10
which are NFC pins that have been converted to GPIO by using macro (CONFIG_NFCT_PINS_AS_GPIOS...
Hi,
which hex file shall i install for an LTE application ?
It is basically step 7 of this tutorial: infocenter.nordicsemi.com/index.jsp
I wanna have a LTE application...
I am trying to start developing on my nRF52833 DK using Segger embedded studios, but my board does not show up as a mounted device on my laptop (echoed by the fact that Segger...
Hi there.
I am attempting to do some reallife tests on the nrf52840, mainly focusing on long-range capabilities and performance between the DK and an iPhone XS. Are there...
Hello, I've seen several posts about this, but I'm a little hesitant to use older posts since you guys put out new and improved versions pretty quickly. We are using SDK 16...
nRF52832 on a nRF52DK connectivity_4.1.1_1m_with_s132_5.1.0.hex pc_ble_driver_py v0.14.2
Steps to reproduce: - connect to a peer device - discover services and attributes...
hello :
1)The packet format of NRF52832 2.4G is as follows, I would like to ask whether the 2.4G CRC can be turned off.
I use two boards PTX and PRX to transmit each...
