Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi,
I have a problem with Secure DFU Bootloader available from SDK 12.1 on nRF51822_xxAA SoC. I use example in SDK 12.1 and when i download it to nRF51822_xxAA it isn't...
Hello,
I am having problems with a custom NRF52840 Board. My program hands at the ble_stack_init function.
I have encoutered this problem in the past so I have tried the...
Hi.
I try to implement LESC using nRF52810.
But I use a Static passkey because my device doesn't have a keyboard or display.
One question is, is LESC more secure than...
Hi,
I try to use QSPI to communicate with Gigadevice NAND flash http://www.datasheet-pdf.com/Search-Datasheet-PDF/GD5F1GQ4 . There's no DK, the custom board was produced...
Hi everyone,
there is a post dated 11 months ago from now in which Nordic tells that -40dBm Tx power configuration is feasible but not recommended ( Case ID: 230320 ). ...
I merged the code from the SDK examples "usbd_audio" and "usbd_cdc_acm" and have ensured that each has their own INTERFACE and ENDPOINTS. I am able to download to the development...
Hi,
I am developing with nRF52832, SDK 15.3
I have an issue with sending data over NUS service. When I flash the code to nRF, it starts advertising, but when I connect...
Dear sir,
The twi sensor code in SDK14 is getting stuck at NRF_BREAKPOINT_COND. Also, on the uart terminal it is showing FATAL ERROR . Please help me out of this.I am using...
Hi
I want to set up a network of about 4 groups of BLE light modules(using the experimental dimming example). Each group comprises of 5 to 7 light modules.
Currently the...
Hello, my code was working just find then I tried to add the user description value to my characteristic. In the example below I had set it to "Test" for now. Once I did this...
hi
i am programing BLE blinky app blinky which advertise. yes, the same code i am trying on custom board works on nrf52DK which has LFRC crystal activated as mentioned on...
I am trying to add my nrfcloud certificate to my nrf9160-DK but the AT commands do not work due to a timeout.
My procedure is as follows:
1) Downloaded the "nrf9160dk_fw_2020...
Hello Nordic team,
I'm getting started with BLE, using the 52832 SDK16 HID mouse example. In the example, clicking the button only moves 5 pixels. How can I move the cursor...
Hi! When measuring current draw with the NRF52 in idle state, we've noticed current spike at seemingly random times. when investigating further, we've discovered these spike...
Hi,
I am looking for an implementation on DotDot App layer over Thread and couldn't find it anywhere. I want to implement dot-dot for Light, Temperature and Humidity Sensors...
