Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I was looking at this compatibility matrix, for SD and SDK.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf52832%2FCOMP%2Fnrf52832%2Fic_rev_sdk_sd_comp_matrix...
Greetings!
we are using nrf5340dk to communicate with a Nucleo shield that has LIS2DW12 accelerometer on it (shield is X-nucleo-IKS01A3). We have a problem communicating...
Hello, I'm beginner for nRF52.
I saw examples about entering DFU by button and buttonless.
Is it also possible that changing the boot mode by a gpio pin which controlled...
Hello all, I'm working on ADC and data transmission.
Device do ADC first, and send those values.
Sampling frequency of ADC is ~80 kHz (sampling per 13 microseconds), and...
Hello,
We are using nrf52805 for our project. Facing some errors like "GATT ERROR" and GATT INSUF AUTHORIZATION and GATT CONN TIMEOUT ERROR" when I want to upgrade my application...
Hi,
We are developing our product based on nrf52382. In the scope of the certification testing of our end product, the test laboratory asks me if the Bluetooth low energy...
I am currently building a dynamic multiprotocol application (Thread+Bluetooth LE) with the nRF Connect SDK. For tweaking coexistence I would like to limit the length (=duration...
Hi,
In nwp-036 page 7,here is the AOD sketch map as below :
As fat as I am concerned, the Transmitter and Receiver should be reverse ?
Or there is something I misinterpreting...
Hi,
Background: I am looking at interfacing nRF21540 (FEM) with nRF52833 (Host) - hoping there's Zephyr support available for this(?)
Question: Product spec for nRF21540...
I'm trying to find the address of an attached twi sensor by using the twi_scanner. It worked on the default pins
but when I change the pins like this
It simply doesn...
Dear Nordic team.
We have to add new sensors using I2C protocol on our previous project.
Can i configure WDIO and SWDCLK pin to I2C pin?
If possible, i will reuse my...
Hi,
I would use the test nRF9160DK and Thing91DK with CMW500 equipment under NB-IOT stanadard.
Both DK kit and Thing91DK can connected to service provider when I plug...
I am working on programming process for custom board using NRF52. I managed to create a merged hex file containing the softdevice, bootloader, app and settings files. I verified...
Hi,
I am using the sdk 17.0.2 and s112.
The Apple Watch can not connect the s112 projects ble, such as 10040e s112 and 10040 s112, But can connect the 10040 s132 ble...
