Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
After implementing my own services, I run into a problem when trying to read the value.of a characteristic. I basically have four services, of which one only holds one...
Dear Nordicsemi,
we need automatic simple test of ble function of our products - scanning bluetooth devices in rage and reading RSSI of device with specific mac address...
Sorry to bring up a topic which seems to have been discussed already, but I don't see an answer to my specific questions.
The original design of my project was to have both...
Hi,
The known issues section of SDK v1.3.0 release note states that
"
nRF5340
FOTA with the SMP Server Sample does not work.
"
Is this fixed in version 1.3.1?
Good morning, I'm working with the nRF52 DK and a custom board that has the nRF52810.
I am using the SDK 15.0.0 and followed the tutorial described here:
https://devzone...
Do you think my nrf is original?
The person I bought says it's original.
Can you please check it?
Seller link: http://www.ebyte.com/en/product-view-news.aspx?id=113
Hi,
I have a custom board in which i am using nRF52840 with SDK version is 16.0.0.
I have tested app_uart library its working Ok and current consumption is 6 uA in deep...
Hello,
I'm developing a project which uses two threads. One configures UART and keeps on a while(1) loop. But once it receives a byte, an ISR pushes the incoming byte...
Hello
I am adding the mpu6050 library in the ble_app_template of SDK 14.2.
Use the ble_mpu6050_simple example here. https://github.com/Martinsbl/nrf5-mpu-examples
I...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi everyone,
Looking the examples of SDK16, I noticed that every example has a hex folder with some .hex files inside . This applies for both peripheral and ble examples...
Hello,
I want flash NRF52840 using AM57xx sitara processor(running on linux) over SWD interface. Can you please provide steps for the same. Is there any other methods available...
Hello,
We are using nRF52840 with SDK 15.2.0, a bootloader and the SoftDevice. We are able to perform a DFU by downloading the .bin and .dat files of the new firmware in...
Hi,
Following the example https://infocenter.nordicsemi.com/topic/sdk_tz_v4.1.0/thread_example_dfu.html how can you connect a jlink debugger and step through the application...
I read here...
NRF52840_PS_v1.1.pdf Peripherals > UART (6.33.7)
“An ERROR event, in the form of a framing error, will be generated if a valid stop bit is not detected...
