At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I need to build a simple BLE dc motor control with a potentiometer to provide the rotational position of the motor.
Anyways, my first step is understanding the Nordic libraries...
I am new at Bluetooth. I want to design remote media control(volume up,volume down, play/pause, next track,previous track) and call answer or reject. I have tried to make...
Hello there,
I am encountering an issue with the zigbee light_control example on the SDK v3.1.
Before I explain the the problem, here's some detail about the system setup...
Hello,
I am attempting to retrieve a device's own MAC address and print it out. So far I have encountered two different functions that can help me achieve this.
void zb_osif_get_ieee_eui64...
Hello
I'm working on the example of app_uart in sdk v17.
I'm trying to create a button 'Long Press' feature, but somehow the button input isn't working properly.
Below...
The example app_onoff.c shipped with SDK For Mesh 4.2.0 (unchanged from 4.1.0) have two unused variables in its state struct.
The value_updated variable looks like a left...
Hi
Is the GPIO on the nRF62840 5V tolerant?
I see the VDD supply is capable of 5.5V.
I’m running a 5V Hall effect square wave into the GPIO pin used as an interrupt...
Hi Team,
I would like to send 10 bytes of data in mesh from one device to another device. As i know that we can send data from one device to another device and the packet...
Hello,
I've asked this question around 6 months ago. Now I have to pick up where I left off and I was wondering how much the situation might have changed since.
- Last...
Hi there!
Okay, I've been trying a lot to figure this out, but without any success. I have absolutely no idea what could be the problem whatsoever. The problem is that the...
Hi,
Currently we working on a project that uses:
nRF9160
Zyphre OS
Segger Embedded Studio for Arm (Nordic Edition) V4.52
SDK v1.3
CONFIG_MQTT_LIB_TLS ...
I am currently unable to flash any new code or to erase the flash memory of my nRF52840 Preview DK boards.
I am using SES and the OB J-Link, but also tried JLinkExe and...
Hi, I am using the TIFS register of the NRF RADIO to define the interframe spacing timing. (Done with the following line)
During a 1Mbit or 2Mbit connection, the real TIFS...
Thanks in advanced. I update uart pin number to rx:10 and tx:9, then get the error as title described under DEBUG mode. To save power, I use uart but uarte, so I set UART_ENABLED...
