We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi, I have very STRANG issues. I am adding custom Characteristics to custom Services. I have added 10 custom Characteristics with the same config 8 of them are working perfectly...
Hi,
I am on ncs master branch, when i build and load the Serial LTE Modem(SLM) application the application struck at mcuboot
The only additional configuration option i...
I am using nrf52840 board. I hvae interfaced a gsm module(quectel m66).The problem is my device gets an APP_UART_FIFO_ERROR after every few sms commands.The maximum data i...
Hello everyone!
I have an issue about upgrading firmware over Bluetooth LE with a mandatory pairing of devices. I want only paired devices to have the ability to upgrade...
hello,
In the nrf51822 sdk 5.1 I can see a routine named ble_app_ibeacon.
I find a parameter define as below,the data is added to the advertising data.
#define APP_MEASURED_RSSI...
Hello,
Our team has narrowed down a particularly interesting issue with the boot sequence / initialization of our BMD-341 chip, which itself runs the nRF52840 SoC. For context...
Hi , i am using the nRF52DK and i have a small problem with the pwm driver.
i basically would like that the frequency increases if i press a button or decreases if I press...
Dear
I have finished completed the Blue tooth Mesh light-switch example function testing , secure button dfu and secure buttonless dfu on DK and dongle of nrf52840 chips...
Dear
I have finished completed the Blue tooth Mesh light-switch example function testing , secure button dfu and secure buttonless dfu on DK and dongle of nrf52840 chips...
It seems like the only way to disconnect the input buffer is using ANAEN, but I know this post says that ANAEN is fake. So I am wondering if there is a way to disconnect the...
I'm trying to upgrade our project from v3.1 -> v4.1 of the Mesh SDK. The BOOTLOADERADDR() macro was re-defined (apparently starting in v4.0?) to use two parameters for which...
Hi,
We would like to access the print outputs of the SEGGER_RTT_WriteString() function via a JLINK compact debugger using Python. The latter is wired only via SWDIO, SWDCLK...
Hi,
I want to integrate HID mouse and HID keyboard in a single device. Can you tell me the complete configuration procedure to integrate HID mouse and HID keyboard in a...
I recently got the nRF52-DK for using as BLE Relay evaluation.
I have downloaded following and installed to run the code
- Segger Embedded Studio (v5.1)
- nRF5_SDK_17...
