Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
Hello
Good day!
Problem: We have got a new nrf52DK, and in our application development we use GPIO interrupts (we have set up 4 gpio interrupts). Surprisingly the GPIO...
Hi,
I'd like to know the units of measurement of the data obtained by the environmental sensors of the Thingy:91 device. I have found no information on that.
Temperature...
Hi,
I am currently working with the asset_tracker example and sending information by LTE-M of environmental and GPS data. I wanted to know if there is any way to calculate...
Hi,
I want to test eddystone example with nRF52833.
The default project doesn't include PCA10100.
I am trying to create one, but it always stuck in the function nrf_crypto_rng_backend_init...
I believe from reading some of the existing posts that my JLink EDU mini programmer (with SWD connection) should work with the nRF51822 (it shows up as a device option in...
Hi,
I want to build a bluetooth central example of zepher to nrf52832.
I am using the command "west build -p auto -b nrf52832_mdk samples\bluetooth\central" to build the...
I'm using 51822 QFAC, SDK11 S130 2.0.0.
I'm able to write to flash using fstorage_write() below. But the problem is whenever I put a for loop after I call fstorage_write...
Hi,
I built a simple custom board with an nRF52832 ebyte BLE module with no added components except for the RST and DFU buttons, the serial wiring are the same pins (RX...
Hi,
I'm working on a BLE scanner which need collect data from the beacon's scan response packet.
As far as I test, the current mesh beaconing example cannot get the scan...
I plan to use nrf52840 in high voltage mode (connected directly to the power source via VDDH pin) with button.
And I plan to use voltage regulator with EN pin (with pull...
The most relevant thread on this topic is two years old. I do not want to use Keil as it is so costly and the project may not go anywhere. I am not interesting in using the...
Is it possible for me to easily modify the nrf52 Zigbee samples to run on 1 or more of my 5340 M33 cores, or is it a rewrite?
I can see chip support for nrf52 but no mention...
Hello,
We recently sent a design to our board assembly house for review and they indicated that the large copper area under the nRF528323-CIAA (WLCSP) may result in head...
I’m using nRF52810 on a custom board (for our own application) using SDK 15.2.0 v6.1.0 S112. Given the amount of memory this chip has (192/24 KB) is it possible to implement...
I'm using the nRF52 DevKit with nrf52832 SoC. I connected a UV Sensor through the TWI interface (PINS 26 & 27, as well VDD and GND).
However, I fear it's using a lot of...
