Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
I try to invert the Signal on a PIN of the PWM module 0. It sould give out the inverted Signal of another PIN from the same PWM module.
I tried it like the code below...
We have problem in background DFU while updating Application with RBP,
Config: MCU : nRF52840 SDK : SDK16 Softdevice : s140_nrf52_7.0.1_softdevice (SDK16)
Case1:Programs...
Hi,
I'm trying to understand how to powermeter bike works. I read the ant documents and execute example bpwr ant code, but I have a question how cadence in power meters...
Hi, is it possible to reset the nvm in the nrf9160 modem back to factory settings?
I've made some changes using CFUN=0 and would now like to reset these back to as delivered...
I have an application using 4 wire SPI connecting to a 2MB data flash. An application using UART (no BLE) works fine reading and writing to this device. However with BLE enabled...
HI
I need to perform some RSA tasks on my NRF52832, but I don't see any RSA files under nrf_crypto folder of SDK v16. I am trying to use RSA from mbedtls external folder...
Hello:
I asked a question a few months ago
https://devzone.nordicsemi.com/f/nordic-q-a/54708/about-nrf52840-save-file-error
However, the follow-up did not get an answer...
Hi all,
I want to run ble_app_uart on my custom board.
I have the nRF52832 (PCA10040) connected with my board by SWD P19, SDK 16. Where should i change to make the code...
Hi, i must change IC nrf8001 to IC nRF5x. Is there an easy way to do this? I need the same same protocol of nrf8001 running on nRF5x for compatibility but with the possibility...
Hi,
I've been following the guide https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_thread.html#mandatory-configuration to get started with OpenThread development...
I have a product that advertises as a BLE beacon. It can be placed into BLE DFU mode through local actions (a command on the USB serial port).
Is it possible to add services...
Hello,
I have a question to ask, I want to beacon the temperature and humidity level in nRF Mesh project here .
Please give me some information or reference code...
Hi,
I developed a software (based on SDK V15.3) that works very well in ESB timeslot with a BlueTooth connection. The softdevice version is s140_nrf52_6.1.1.
Today, I...
I am new with the nRF52832. I need to develop a bluetooth slave port for an existing controller. The controller will communicate with the nRF52832 via the UART. For prototyping...
