Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hello,
I am working on a custom nRF52840 module based board, using SES v14.2.
How can I control what is printed on the debug terminal, or what has highest priority to...
I have a BLE device for which the local name contains and apostrophe. When I run nRF Connect on an Android phone and view the raw data for this device I find the apostrophe...
Hi all,
I have an nRF52 acting as Central, and it will act as beacon just when it, for example, reach a temperature above a certain point. After some time, e.g 10 calls...
Using SDK15.3.
Using the logging in deferred mode with RTT viewer.
Getting the errors below from the macro expansions but I can't identify what is missing.
Went through...
Hi,
I made a temperature logging device using nRF52832 (SDK 12.3.0). The temperature sensor is read over I2C every 5 minutes and data is sent over radio communication. There...
Hi,
I have setup the SW project to run run FreeRTOS with BLE stack initialized and nus service started without doing any further BLE use after init in runtime. Sometime...
Hello,
I am using an Adxl362 accelerometer on nrf9160 dk board.
I followed the tutorial a to add the overlay file and even configure the pins i want to use by flashing...
To the kind attention of Nordic support team,
It seems gazell is a very good candidate to be used in tipical working environments, where a bunch (<= 5 devices for example...
Hi,
I am new to Nordic. I bought an NRF52 DK and a Fanstel EV-BT832 development board. As you can see in the picture, both boards are connected to the computer via USB....
Hi,
I had some of your example projects which were being evaluated within Keil and SEGGER and now have an issue with Keil after updating to the PRO license.
I now get...
Hi,
For a peripheral reset, I was recommended to use the code below.
I was just wondering about what the middle line does. Is this a kind of delay to make the reset...
I am trying to start the mesh alongside GATT profiles. I am getting error NRF_ERROR_NO_MEM when calling sd_ble_gap_adv_set_configure in mesh_adv_data_set, which is called...
Hello,
I get the following output when I try to debug the Zephyr's button sample with SEGGER Embedded Studio:
Preparing target for download Executing Reset script TargetInterface...
For the nRF52833:
The product specification is contradictory on the 2 UARTs available. Would you please clarify?
UART0 is this a legacy UART only or does it have Easy...
Our customer has requested access to any test suites the BLE IC vendor can provide which can be used to provide objective evidence of testing & specific test cases.
We started...
