After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi,
We were trying to flash the nrf modem firmware using the 'pynrfjprog'.
When only one nrf9160dk is connected , the flashing is success and no error.
But when multiple...
Hello, a question about this link:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Flib_bootloader_dfu_process.html
which says...
Hai,
We are using RTC in one of our project (in nrf52832).
RTC is working fine. I am waking up by every 30 mins once. But I am not able to configure same RTC instance...
I have an end device acting as a server, and I need to send data to a bound client. This is custom data, so I cannot use a reporting attribute. Basically I need to access...
Hi,
I am absolutely new to this DLMS and in the course of exploring some kind of opensource DLMS stack I came across this Gurux and fortunately NORDIC did some kind implementation...
Hi,
I am developing an ESB application with 1 central (nrf52832 DK) and several peripheral. The peripheral are nrf52832 + ICM 20948. Development is done with Segger embedded...
I am trying to setup development environment by following below steps.
The nRF Connect SDK Zephyr repository contains a list of required Python modules. Install these modules...
Hi,
I have bought NRF24LE1 module. Now I want to program the module. So, will anybody please suggest me which programmer should I use to write hex file ? I have mPro programmer...
Hi,
I am currently trying to implement a beacon scanner alongside peripheral mode BLE on an nRF52832. As I am only scanning for beacons, I was hoping I would not need to...
I have been trying to connect to 4G using iBasis and other vendor's SIM card but have not been successful.
I have the nrf9160 DK two years ago and have been sparsely trying...
Hi,
We have 4 NRF52833 DK being used for our development work.
Among that, 3 of them have stopped working and are not powering up.
They power up some times when connected...
Hi,
to develop a device driver in Zephyr for TI DAC80501, a 16-bit DAC, I2C interface,
I have to
1. add the dts child node under the i2c controller node
$i2c1...
I'm using the asset tracker project and I want to add in the ability to store information on the board. However when you include the littlefs file system you get a build error...
Hi Team,
We are using the nRF52840 board for our development purpose. We are using the external debugger(i-jet) for our development purpose.
We are able to connect the...
I have a firmware build that uses the nRF52832 (SoftDevice S132) to return a variety of read characteristics to an external device. So far so good. I can verify that the values...
