Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hello
Would someone ,please reply to the below thread,waiting for the response
https://devzone.nordicsemi.com/f/nordic-q-a/60891/unable-to-read-the-128-bit-uuid-with-base...
Hello how are you?
I'm using the mesh example Light switch example from nRF5 SDK for Mesh v4.0.0. I implemented the RSSI util model and it is working, one question I have...
I am working on a new design and i am using ST7789 (240 X 320 pixels) screen with nRF52840, it is working fine. I have followed the code provided in SDK example (big thanks...
Hi,
I´m trying to add a new, custom TX characteristic to Softdevice. I use example from SDK 16 "UART/Serial Port Emulation over BLE".
How I can do this, is explained...
Hi,
I flashed and run "ble_app_uart" example on nrf52833 DK. With an UART tool, I can recieve data from smartphone (rx characteristic) but I can´t send data from UART tool...
The sdk 16 - bootloader positions s140 softdevice V. 7.0.1 wrongly so that it is acknowledged as Application and does not work with nrf52840.
As you can see at the picture...
Is there a place to make suggestions for new releases of nRF5 SDK's or even contribute?
I've been using the current USBD CDC ACM library and needed to modify the app_usbd_cdc_acm...
Hi , I am making a zigbee application to write attribute on remote node. Please share the application structure to implement writing functionality of attribute on remote node...
Hi,
I am trying to test PSM settings on the nRF9160 using a custom PCB. I have set the active time to 3 minutes with a periodic TAU time of 10 minutes.
When the device...
I’m developing an application based on pc-ble-driver to talk to an nRF52840-based dongle (from Fanstel).
I’m having trouble disconnecting cleanly when a connection has operations...
Hi,
I´m using the NRF52810 device and have an issue with the SAADC peripheral.
I basically have 2 channel where i want to do some averaging to improve noise.
The setup...
Hi,
I was exploring TWI master with TWIS Slave example in SDK16.0.0.
It works for sequential reads in loop-back mode.
Now I connected the simulated eeprom slave...
hi, I set up the environment according to the nrf_sniffer_for_bluetooth_le_3.0.0_129d2b3 file downloaded from the official website of nordic, the operating environment is...
Dear Nordic Team,
we have unstable communication with an Osram BT device through nRF52840. We got information from Osram developers the nRF52840 is the right device for...
