Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi ,
I am using the code that is built-in and I want to know about the Security manager. I want to see the encryption is enabled or disabled. What is the command? If I want...
Dear Community;
I am trying to read serial data sent by a PMS 5003 in hexadecimal. If I connect the PMS 5003 to a conventional serial device (Raspberry) this is what I...
Hi, I've recently updated to the latest NCS repo. I'm not entirely sure what version of NCS i was on before (perhaps if you could tell me how to check - as i made a copy of...
Hi, I am following the below link for creating custom services/characteristics. https://github.com/bjornspockeli/nRF52-Bluetooth-Course 1-I have added the notify part but...
Hi,
I am working on the MG996R servo and MG90S with nRF52840.
I am using the following delay logic to operate MG90S. (As per datasheet)
MG90S is working perfectly fine...
Hi ,
Just one question.
I am trying to create services using hrs examples and its useful.
Currently one question I have that ,
the battery indicator is only notifiable...
Using: Windows 10, nRF Connect v3.5.0, nrf v1.3.0, zephyr v2.3.0
I have a board based on the Thingy91 and the Asset Tracker application. I verified serial console output...
I want to quickly send up to 100KB of data to a connected smartphone and then disconnect to save battery.
I have most of this working using the NUS service but today I noticed...
Hi Team,
I would like to perform the DFU without using the nrfutil and OTA update. Is there any way to perform DFU without the nrfutil.
Our requirement is - We have...
Hello,
i built a SPI Master example based on this: SPI Master example
The example is a bit outdated and needed some rework and fix to work. I don't know if i am missing...
Hi.
NRF52832 is used as central for connecting with phones as peripheral. NUS service is used. Lesc is used too.
SDK 17 SoftDevice S132 V7.0.1
I have sometimes crash...
Hello,
From some time now i have been tryng to start developing an app, but i encountered a problem where the board does not connect, or does not find a provider from the...
Hi,
My goal: F lash hci_usb in my nRF52840 Dongle, so that i can use Bluez stack in my Linux host and nRF dongle as BT controller.
Build status: Success
Flash : Failed...
Hello,
I am trying to find the electrical and timing specs of the nRF52832 SoC. Where can I find them? In the Product Specification document they are not given.
Thanks...
