I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi, I am looking where can I get the ACK from the light bulb, in Zigbee light control example. I am using the latest sdk nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.
what...
Hi,
The documentation for the simple_on_off model in the nRF5 SDK for MESH v4.1.0 states that the light_switch example uses the simple_on_off model.
The documentation...
I think spi slave pins should set as input but I want to control CSN pin as output in spi slave mode on nrf52840. Is it possible it?
I know that CSN pin is controlled by...
Thingy91 is useless without working samples and SDK
Out of the box it cannot associate with any NB-IoT cells here in Bulgaria. I tied using the provided SIM card from iBasis...
Hi I am having some trouble changing BLE connection parameters (mainly due to the connection handle). Is there any working example that I can refer to, which explains how...
Hi Nordic folks,
Our project is using nrf52840-DK boards as the development beds. We're developing a security application by leveraging the internal CryptoCell CC310 inside...
Hi everyone,
I successfully tested the example of the MQTT publisher in the IOT sdk on a NRF52840 and a raspberry pi 3+. The messages end up in my mosquitto install and...
Hi,
We have seen random ARM faults.
After some time we have seen that the lr register often pointed to entropy_cc310_rng_get_entropy.
This is our setup:
- Environment...
I recently purchased nRF52840 DK. While scanning through the website, I came across a suggestion to start with Blinky example. I opened the project in Segger Embedded studio...
Hi,
Observed that Openthread CLI project in NCS v1.3.0 is not compiling as it is using Segger Studio but building with command line. Please fix this.
Thanks
Sridh...
Hi Nordic experts,
I am trying to use Segger IDE to build the mcuboot boot-loader for NRF52x development kit. I am using NRF connect SDK 1.3.0 While I can build it successfully...
Hi
I am facing two issues in the below code. I use segger embedded studio.
1.The value I am setting as fs_initialized = true in line number 90 (inside FRESULT fs_init...
Hello,
I'm working with nRF5 SDK v16.0.0.
The documentation on Hardfault handler implementation clearly suggests to define DEBUG_NRF in order to get an automatic breakpoint...
I have the Thingy91 module, everything is working when I (turn off modem then) set AT%XSYSTEMMODE=1,0,0,0 (and turn on modem again), but if I power cycle the device the original...
