I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I have added the include and src. file paths to the MAKEFILE and yet I am experiencing this error.
I tried deleting the main.c.o file too, but am still experiencing this...
Hi,
After implementing my own services, I run into a problem when trying to read the value.of a characteristic. I basically have four services, of which one only holds one...
Dear Nordicsemi,
we need automatic simple test of ble function of our products - scanning bluetooth devices in rage and reading RSSI of device with specific mac address...
Sorry to bring up a topic which seems to have been discussed already, but I don't see an answer to my specific questions.
The original design of my project was to have both...
Hi,
The known issues section of SDK v1.3.0 release note states that
"
nRF5340
FOTA with the SMP Server Sample does not work.
"
Is this fixed in version 1.3.1?
Good morning, I'm working with the nRF52 DK and a custom board that has the nRF52810.
I am using the SDK 15.0.0 and followed the tutorial described here:
https://devzone...
Do you think my nrf is original?
The person I bought says it's original.
Can you please check it?
Seller link: http://www.ebyte.com/en/product-view-news.aspx?id=113
Hi,
I have a custom board in which i am using nRF52840 with SDK version is 16.0.0.
I have tested app_uart library its working Ok and current consumption is 6 uA in deep...
Hello,
I'm developing a project which uses two threads. One configures UART and keeps on a while(1) loop. But once it receives a byte, an ISR pushes the incoming byte...
Hello
I am adding the mpu6050 library in the ble_app_template of SDK 14.2.
Use the ble_mpu6050_simple example here. https://github.com/Martinsbl/nrf5-mpu-examples
I...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi everyone,
Looking the examples of SDK16, I noticed that every example has a hex folder with some .hex files inside . This applies for both peripheral and ble examples...
Hello,
I want flash NRF52840 using AM57xx sitara processor(running on linux) over SWD interface. Can you please provide steps for the same. Is there any other methods available...
Hello,
We are using nRF52840 with SDK 15.2.0, a bootloader and the SoftDevice. We are able to perform a DFU by downloading the .bin and .dat files of the new firmware in...
Hi,
Following the example https://infocenter.nordicsemi.com/topic/sdk_tz_v4.1.0/thread_example_dfu.html how can you connect a jlink debugger and step through the application...
