Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Dear Nordic:
I used V2.8.0 SDK to build light bulb, and I have commissioned bulb A(node id: 11) and bulb B (node id: 11) successfully!
Then I used below command to add...
Hi,Team,
I'm using the nrf54l15-dk to develop zms to save custom configurations without affecting the pairing information of ble.
So I have a few questions: 1.Is the storage_partition...
I am trying to set up FOTA support with external flash for mcuboot secondary partition. I have gone through several tickets on the subject, but haven't been able to solve...
It might be due to a short circuit caused by incorrect wiring. The PPK2 circuit board is damaged, and the chip with silkscreen "L7 #247" in the lower-right corner seems to...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Description:
My nRF52 DK has stopped being recognized by my PC. Below are the details of the issue:
Kit Info: PCA10040 v3.0.0 (2023.22), nRF52832 target MCU
...
Both computers have ncs2.9.0_nrf54h20_1 SDK installed
The same project is compiled on these two computers, the firmware zephyr.hex is different, but the zephyr.bin is the...
hello, I encountered a problem using TWIM to communicate on nrf54l15 Software and hardware versions: Using ncs V2.8.0 version. The hardware is NRF54L15 RevB. The compilation...
Hello, I connected my (working) PPK2 and opened the PowerProfiler. Immediately, a "DFU needed" message popped up.
I DFUed the PPK2, and in the logs, it wrote DFU successfully...
I'm having trouble porting my project from the older SDK (2.6.0) to the new SDK.
I thought the most straightforward way to do that would be to start with a sample project...
Hello all,
I am having issues with the configuration of the FEM nRF21540 on the costum board Fanstel BT840NE with the Enhanced ShockBurst (ESB) protocole.
We are not able...
Hi
I have a project using winc1500 as WiFi module, base on example wifi shell example and post
I add:
CONFIG_WIFI_WINC1500 =y
CONFIG_WIFI_WINC1500_REGION_ASIA...
Hi,
I want to write data to a specific memory. I understand there is ZMS.
https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples/subsys/fs/zms/README.html#zms...
Hello,
I want to perform some antenna measurements and compare the rf performance of my custom PCB with an nrf9160 SiP with the nrf9160 dk.
To perform some antenna measurements...
Hi to all,
I am trying to do a ZUTH (Zigbee unified test harness) test run, using the Silabs devices as golden devices (as per CSA recommendation) and nRF 52840 dongles...
