I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello all,
I am using the example \ examples \ ble_peripheral \ ble_app_uart Right now I'm having a problem that I cannot use FDS. My fds_event_handler I never see case...
Hi
NRF52810
SDK 17 SoftDevice S112 V7.0.1
We have migrate to nRF5_SDK_17.0.0 from nRF5_SDK_15.3.0_59ac345
Central on chip nrf52832 has migrated successfully
...
Hello Everyone
I have an Interrupt Signal at 8MHz after which I need to execute some stuff. I set up an Interrup on an GPIO Pin to test it but at around 4MHz the nRF5340...
I develop a pcb based on the n52832 chip, when the reference of the chip is n52832 qfaae1 all works good, but when i use the n52832 qfaab0 chip it's unprogrammable.
i'm...
Hello
I want to test the nrf52DK board by connecting it to the battery. However, the reset button does not work when only the battery is connected.
To activate the reset...
Hi,
I have three nRF52 DKs，instance is “ nrf5_SDK_for_Mesh_v4.2.0_serial”。When I send commands from PC (UART) to DKs ，DKs running well，but often no response from DK （UART...
We are going through regulation certification testing. And lab is asking what is power tolerance for BLE 1Mbps for the chip. Where can I find this value?
1.Cant make P0.09(NFC1) and P0.10(NFC2) outputs?
Tried both nRF52832 from PCA10040 and a BT module with nRF52840 and on both cant make any of those pins outputs. Tried with...
Hello
I want to test LE Coded PHY S = 2 (500 Kb / s) using the nRF5430 PDK. The SDK used is nRF Connnect SDK v1.4.0.
There is confirmation there.
1. Does nRF5430, nRF...
Hi there,
I am developing an application that uses UART. I am wondering what's the proper way to connect the nRF52840 to the PC. I researched online and found that I could...
I have a few nRF52833 development kits and want to get started with Keil (MDK-ARM). I could not find example projects in the packs that run on the PCA10100 board. Beside of...
SDK 15.3.0, code is based on examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput.
After getting the project to work with nRF Connect on the desktop...
