Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
DK is not powering ON suddenly.
All the Power Switches are selecting properly (SW8 = ON, nRF Power source = VDD, SW6 = nRF ONLY)
USB is connected to J2 Connector.
Observations...
Has anyone been able to connect the nRF52 to MATLAB using their new Bluetooth Low Energy Communication interface ( https://www.mathworks.com/help/matlab/bluetooth-low-energy...
Why is "No location data available" always printed when SUPL data is downloaded in gps sample app? This happens at any place. I guess this causes a long TTFF.
This is a...
Hello. I have a DK nRF9160 0.8.2 version. I am sending AT command through UART with an external MCU (STM). I am interested on evaluating power consumption during an UDP packet...
Hello,
I am trying to integrate OPTIGA Trust X with the OpenThread example, "mqttsn_sleepy_subscriber"(from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0 SDK). I tried adding...
Hello.
I am running Segger studio 4.5 on Windows 10 and the ble_app_uart example project that works fine with one connected central device (i.e. iPhone with nRF Toolbox...
Dear all,
I'm using nrf52-DK with PCA10040 as sniffer. I develop 2 custom board (nRF52840) (one acting as master, one as slave) and I would like to make some considerations...
Hi,
I have develop an application using the nrf52832 combined wit the ICM20948 sensor.
The application use ESB communication between peripheral and central. I have solder...
Hi,
Keywords: nrf52832, pwm_driver, two pwms, 6 channels, pwm in sequence
I have four LEDs: three mono white LEDs, one RGB LEDs(three color leds) that produce white...
Hi,
I use usb_msc in nRF5_SDK_15.3.0_59ac345 use case, format file system and create folder and its subfolder test, found that segger development environment compiled programs...
Hi
I have followed the all the instructions with regards to 'nRF9160 DK Getting Started' and all is fine until the stage "Building and testing a sample application" where...
Hi Team,
We need to enable the two crypto backends one is CC310 and mbed TLS at a time for our development purpose.
Why means one of our features used 128 bit AES ECB...
Hi, I need a little help with understanding to implement security in my application.
Most examples used by Nordic have public advertising on, so any device can connect to...
Hello I'm working with Zigbee Dimmable Bulb example. Testing environment is as followed:
nRF52840DK SmartThings Gateway SmartThings iOS app.
After changing the Zigbee...
