Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hello,
I run the example given in SDK V15.0.0 to measure Vdd of nRF52-DK:
NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_SE(NRF_SAADC_INPUT_VDD);
I don't change the default...
Before I explain my issue I wanted to be sure on my basics, so here is my understanding after doing the research in nordic devzone
I'm using nrf52832 with sdk15
1) BLE...
I am using nRF5_SDK_15.0.0_a53641a.zip to create an application needs paring and bond. Now I got a problem that, if a smartphone removed the bond manually in its phone settings...
Hi
I’m using NRF51822_XXAC + s130_nrf51_2.0.0_softdevice, my program work well most of the time, but it dies at 0x000006b0 sometimes. Since I used the S130 softdevice, the...
Hello, guys,
I develop 52810 with sdk 14.1.0, i need the OTA features,
but i couldn't find the dfu demo( ble secure dfu bootloader and
buttonless dfu template app , pca10040e...
Hello,
As we know that nRF52840 SoC supports Bluetooth 5's 4x Long Range and 2x Data Throughput.
How different PHYs for these features (2 Mbps PHY and 1 Mbps Coded PHY...
Hi,
I am using nRF52832 to design a mesh system, starting with light.
Everything is fine, and development is reaching the end.
Before today, I use only one model,...
Hi there!
I had some great help on my last article about getting started. I'm now using Segger Embedded Studio and the nRF SDK Version 15.
Before I get too deep into BLE...
I'm developing multiple peripheral and a central. Central is only scanning and Peripherals are only advertising.
In the example, I see that I should use the ble_app_blinky...
I get a BLE_HCI_CONNECTION_TIMEOUT error when I use NRF connect to connect to my dev board only when my dev board is using SD 6.1.0.
Once I get the error I have to reset...
Hi, I am new on BLE development and a bit confuse on choosing development kit. After search around, I learned the following, please tell me if any wrong:
Segger JLink...
I am trying to debug the DFU in IAR. I realize I will have to turn optimization off and grow the flash size in the linker file. However, when flashing as is I get the following...
