I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Hello,
What is the switching frequency of the buck regulator integrated into the nRF51822?
The characteristics of this regulator do not seem to be explained in the documentation...
I'm following the Custom BLE Service Example , and using:
Segger Embedded Studio Release 3.34a
macOS 10.13.4 (aka High Sierra)
nRF52 DK (PCA10040, nRF52832)
nRF5_SDK_15...
Hi,
I am investigating an alternative to an implantable device that currently uses NFC.
The device range would only be about 3m and the data would only be transmitted...
this packet is capture by wireshark .I use nrf51822 and sdk12.3 connect Balance car,but the packet not have LL_VERSION_IND, LL_FEATRUE_REQ、and LL_Connect_UPDATA_REQ these...
Dear Nordic Team,
Thanks for supporting.
now i am workwith secure dfu. I followed this link https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure...
hello
I am just starting to use the nrf52832 .
I design the PCB with nrf52832 and want to load the softdevice.The nrf go studio can not detect the nrf52832, but the keil...
I was facing some issues getting PWM peripheral work on my custom nRF52840 board. And then I tried the pwm output on P0.08 instead of P0.06 and the signal came out just fine...
We're developing a new device for a regulated market (medical). As such, we need to have control on what third-party software we're using, and how it is working. While starting...
I wanna implement this code for the app inventor, but there was several problem here. I can't use array or index for developing my trapezoidal method.. like this..
code...
Hi All,
We have build a BLE beacon device based on the nrf52 chip. The device works fine but we would like to get a finer control over the TX power since it is used for...
compiled nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_rscs example but will fail on adding chararteristics in char_add() setup: SEGGER Embedded Studio for ARM Release...
Hi guys,
I am trying to use a TM2001 amplifier ( Taiwan Microelectronics, google returns the PDF) to amplify the signal from an nRF24L01P.
The TM2001 seems to accept a...
Hi.
I want to create Bluetooth mesh network and I need that each of device at first must be provisionee, but if in a minute it hasn't been added in a network by provisioner...
Hi
I was designing a custom board for nrf52832. The 32MHZ crsytal mentioned in the refrence design of nrf52832 is not available on digi key. So I am ordering the below given...
