I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
Hi everyone and thanks in advance.
I'm new to the NRF52 SDK enviroment and I've been having some trouble with the I2C/TWI configuration. The SDK we are using in the v12...
Hi,
Is it possible to send notification periodically even if there is no change in the value? I create sample code that send constant value periodically over BLE, but in...
I'd like to use new nrfx drivers included in SDK 15. The problem is that I want to use C++ but nrfx header files are for C. The struct initializers can't be compiled as C...
I have a lot of pin_read function. How can i set all port one line? for example P1OUT = (P1.01 | P1.02 | P1.03) or P1IN = ( P1.01 | P1.02 | P1.03 ) I dont know how to use...
I created a simple message mode based on the simple_on_off modle,when I debuged the codes in simple message client,I got an error(app_error),I never changed the codes for...
hello,
I used NRF52832 as a ble gatway.Now i have a trouble that the received signal strength is jumping about 2dBm when the chip loaded program.I test it with Spectrum Analyzer...
Hello! I am trying to prototype a DFU solution that works well for our application. We want to build a network with both normal Mesh devices and with friend nodes (once that...
Hi,
for my PCB, i'm using an NRF52832 as SPI slave, i send an array of 4 bytes {0xA5,0x00,0x01,ff}, but my SPI master receives always a byte (0xff) before 0xA5.
this...
Hello everyone
I have kind of a basic question.
I'm not sure how to manually disconnect from a ble connection. I'm using the ble_app_uart and ble_app_uart_c examples from...
Hey all,
We’re trying to figure out the best way of keeping our nRF52 (or 51) based design in the lowest power mode possible while sitting in inventory.
Currently, our...
Greetings,
I have 12 sensors each of which is located on an nRF52832 board. I need to collect the sensor data at 50Hz (10 bytes for each sensor).
For some reason I can...
This one is throwing me for a loop.
We just did a small build of 40 devices based around the nRF52832. 1 device out of those 40 is behaving very strangely. When the device...
Hi Sir
I want change the power transmission level for measuring the RSSI values for different configuration from -40DB to 4DB. for that i configure the radio. But it is...
When compiling (after the project folder change and paths updating) I get always this error.
No idea why. The C99 option is choose
It compiles correctly from SDK tree...
Hello,
I just finished migrating my project from SDK13.1 to 15.0. It caught my attention that when I flash the Softdevice, it uses memory from pages 0x00000 - 0x24000. I...
