I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
Hi,
I am new to Nordic's softdevice based development and I want to build a basic application for advertising to understand more about the softdevice. I went through the...
I know this question has been asked before, but I couldn't find an answer...
I'm looking for an example of how to use the nRF52832's SWO feature with the SEGGER JLink product...
Hi. I am using nrf52832 SoC with s132 device (4.0.2). Device is acting as peripheral, I have set max BLE connection limit to 1. ble_cfg.gap_cfg.role_count_cfg.periph_role_count...
I'm following the migration guide from SDK 14.2 to SDK 15 , and am a little hung up on the new nRFx module.
All the examples in the new SDK use the legacy drivers but the...
I'm using the CR2032 to power up my nrf51822 with LDO setup, it works well in the begining. But when the voltage drops below 2.6V, my phone cannot scan the BLE. Is it little...
What is expected behaviour of s132 device (4.0.2) if peripheral is initialized with periph_role_count=1 and somebody tries to connect when BLE connection is already establsihed...
Hey Guys,
I'm a newbie on BLE development , I'm trying to run the example "examples\ble_peripheral\ble_app_ancs_c" , It works well first time, but it cannot receive the...
I'm using nrf52832 powerd by a 3.6V regulator in a li-ion powered application. And using one of the IOs (P0.05) as the power supply of other circuits.At the same time, using...
Hi
I am having trouble getting the basic BLE_APP_UART up and running. The UART printf() works, but the BLE module (NORDIC_UART) is not visible in all the devices android...
hi,
i am doing a project where i am using central and client model.
i am using nrf52840 as central device and thingy 52 as peripheral device and i am using sdk 14.2.0...
When using make flash on an SDK11 sketch, s132, pca10040, on Ubuntu 18.04, it successfully builds everything until app_uart.c; when it gets to that point, it outputs the following...
Hello,
I would like to test my code on a NRF52832-QFAB chip with 256kB chip to see whether my code fits into the 256kB flash variant.
According to nRF52832 Rev 1 Errata...
hello
i am using segger embedded studio. with nrf52840 and sdk15.
i was working to set the clock using nrf_clock_lf_cfg_t which is defined in nrf_sdm.h .
nrf_sdm.h is...
Dear Sir/Madam,
I am working on a 51822 project which send data to Android App. This project is actually an replacement to an old BLE sensor which is obsolete now. I have...
