Hi,
I'm using the nRF52833 to develop a BLE beacon and built a Bluetooth gateway for my application.
Application Requirements:
The beacon should advertise using...
Hello,
I want to perform some antenna measurements and compare the rf performance of my custom PCB with an nrf9160 SiP with the nrf9160 dk.
To perform some antenna measurements...
Hello - I have the exact same question as proposed in this thread - I am wondering if there has been any change in the 3 last years since it was posted.
In a nutshell, we...
Hi I want to build a multi role BLE device.
As a peripheral it shall stream ADC data with arounf 20 kbytes per second.
As Central it shall receive adv_nonconn_ind packets...
Hello everyone,
I have an nRF5340 microcontroller (NORA B106 module), and I want to connect a square wave signal to one of its pins to read its frequency or count the number...
Hi,
Hope you are doing well.
I would like to use eSIM on nRF9151-DK board and an eSIM has been assembled in the board. However, eSIM is not detected.
According to...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
there are proxy client and proxy server in the light switch demo of mesh sdk v2.0.1.the proxy client can't be provisioned after i had provisioned another client,is there only...
Just starting development with nRF52840-Preview-DK using Bluetooth Mesh.
I've loaded compiled, Light switch server example code for nRF5_SDK_for_Mesh_v2.0.1 along with nRF5_SDK_15...
Dear all:
I want to know how to demo the proxy client & proxy server ,I can't find the way to demo the two samples which like the PyACI do .
For example ,I can use a button...
Hello,
I am develop a project with nRF52832 and I use nRF5_SDK_14.2.0 and softdevice s132.
My problem is I need create a variable that maintains the value after of the...
I have configured nRF8001 with Arduino M0 Pro board and its working properly. Now, I want to add passkey to my device but it dont have display/ keyboard , only one power button...
I have nRF8001 configured with Arduino M0 pro, and I am having problem regarding how to set static passkey. I came across the fact that softdevice API can store static passkey...
Hi, I just recently bought nrf52832 dk board. I am really new to this. I have prior experience on Arduino only. I started working on nrf52832 dk board with the help of nordic...
Dear Nordic Team,
We are using nRF52832 with a IQS231A for proximity detection for a new product, the pins are connected to SDA and SCL and everything is routed as in...
I am now using nrf52832 sdk14.2 development, as a slave device, I want to set the slave's Bluetooth interval is 1S, I set the following parameters: #define MIN_CONN_INTERVAL...
Hello,
I have nRF52832 with custom board and using SDK15 with Keil uVISION 5. I am working on beacon example and I have modified it to show battery level. I have done necessary...
I am using the bootloader_secure_serial example from the SDK 14.0.0 on a 523832 DK. I have erased the device and flashed the softdevice and bootlader on it. The LED1 is turned...
Hey, I would love some guidance on this:
1. I have one NRF52840 advertising constantly at 8dbm, this device is connected to power so it's hard coded to the maximum transfer...
Greetings,
Based on your librairies/examples, I can succesfully write and read data from an external flash (MX25R6435F) using QSPI with DMA.
I'm using a custom board with...
Dear all
I am on the pca10040 board (nrf52832), and I see the "Thingy_bridge" program is pca20020 board, as shown in Figure 1;
I am in the burning process, the simulation...
hi, im using ble_app_uart and im trying to do a simple communication and data transfer over bluetooth with my iOS.i want to send from the Bluefruit app a byte (0x55 for example...
