Hi,
for a couple of weeks (maybe months), I've been getting the following error indication when performing a pristine build on my projects:
The terminal doesn't show...
I am working on a nRF52832 NFC tag application. If I use a NFC-enabled smartphone to write a text message to the NFC tag emulated by nRF52832. The nfc_callback c allback function...
Hi all,
lesson2, excercise2 is missing the code snippits.
Excercise1 and excercise3 do have code snippits to copy.
I tried on both Chrome as on Edge, but the snippits...
Hello,
We are in the final stages of development with a board that combines the nRF5340 with the nRF7002. This board also requires native USB support and we are routing...
We are using the nRF5340 with Zephyr OS v3.6.99-100befc70c74 and nRF Connect SDK v2.7.0-5cb85570ca43. We have the following questions:
Is our understanding correct that...
SOC: nrf52840
SDK: v2.9.0
Device is a central, it connected to 16 peripherals, these peripherals will power on 90 seconds and then power off 10 seconds(one cycle). ...
Hi,
I have successfully updated the firmware on the nRF5340DK controller using the DFU MCUBoot method. Now, I need to add Secure Boot NSIB to the bootloader and integrate...
Our application needs to read 128 bytes from 6 SPI sensors as efficiently as possible. We're currently using a single SPI Manager to read all 128 bytes from all 6 sensors...
Hi all.
Just wondering if i need to go through the tutorials on making a service if i just want to read a few bytes in an advertising beacon.
I'm a little lost on figuring...
Hi ,
I am using a bluetooth peripheral which have the Custom Service ID and characteristics ID as below.
Service UUID: 56494B01-0100-1000-8000-00805F9B04E1
Characterisitics...
Hi,
We are currently developing an application that makes use of soft device(s112). We tried using timer(Timer 1) for a timed wake up and sleep but found that the actual...
We are seeing an LMP PDU error when connecting to a Nexus 6p with Oreo (8.0.0) when connecting to an nRF52832 utilizing SDK 14.2 and either s132 vs 5.0 or 5.1 anytime NRF_SDH_BLE_GAP_EVENT_LENGTH...
Been testing custom_ble_service_example , specifically to see if a two byte custom_value can also be used.
But when setting custom_value to uint16_t I get a warning at this...
Hi, I would like to use a PWM application with mesh SDK. However when I try to compile, I got an error because "app_pwm.h" is missing (No such file or directory). The only...
Hi !
I'm using the nrf52832 chip and I'm trying to communicate with a LIS2DH12 accelerometer using the I2C protocol.
But unfortunately I can't handle with it, it seems...
Hello,
I am completely new to creating a Bluetooth mesh network and nRF5 devices. I have three nRF51 DK and 2 nRF51 dongles. I have earlier read the posts and made nRF51...
Hello,
I am using sdk12.2.2 and customised nrf52 board. I am writing 6000 records of 24 bytes each in flash of nrf52. My challenge is after 6027 records I am getting error...
i made custom board refer to thingy 52 Circuit
all fuction circuit is same so i want to use thingy 52 firmware
when i was erase all memory nrf52832 and upload thingy_v2...
I am using nrf52832 sdk14.2.0 to develop now, I want to realize the following function on the basis of PWM_driver example, output the following waveform on P0.22: 1ms high...
Hi all,
I am newbie with nordic, and I need some help.
I am using nRF52832 with softdevice.
I need to generate a 128 kHz clock signal (PWM pulses with 128kHz frequency...
Hello,
I'm doing some power evaluation of the three PHYs of BT5 using the PCA10056 preview (v0.9.0) and the PPK (rev 1.1.0), moreover I'm using the ble_app_att_mtu_throughput...
