after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi folks,
I try change blinky code for nRF52810 SoC. I must create own timer. I dont know app_timer example help for me?! I want to do when power on leds on 2 seconds...
Hi All,
I am developing an application in which i am interfacing the nRF52832 with an ADC via SPI.
I am doing channel multiplexing (2 channels) such that when i get data...
I'm aware of the limitations on using "printf" in a non-debug environment, but apparently there must be something similar with sprintf. I'm using it to load a value into a...
Hello,
There's a problem compiling the standard ble_app_uart_pca10040_s132 in Segger Embedded Studio for ARM V3.40. The UART example is straight out of nRF5_SDK_14.2.0_17b948a...
Based on the demonstration video of Thingy , I can have a view on Thingy is changing its color when it is given different command using the apps.
1. As if I want to send...
Hello, I want to include Mesh Serial Example into the Mesh Light Switch example.
The aim is to allow the serial device to listen to the mesh messages.
What is the best...
Hi Everyone
I am using BLE for NORDIC UART SERVICES. I want to update my code via BLE instead of a USB or J-LINK.
How can i upload my code from the Android device to nrf52840...
Hi,
I am working on nRF52840 board using Segger Embedded Studio for ARM 3.34a on windows 7 64 bit setup.
I am trying to bring up UART on my custom board.
So as a first...
I followed test steps mentioned in dfu_quick_start.md file to perform DFU over mesh.
1. Below is the error i am getting while creating DFU package, Please help on this....
Hi,
I am working on nRF52832 board using Segger Embedded Studio for ARM 3.34a on windows 7 64 bit setup.
I am trying to erase page from RAM using "nrf_nvmc_page_erase...
I have a situation with the devices my company builds. From what I understand, they've been designed with a small flaw, which causes them to sometimes get stuck and require...
51822 problem: the device unexpectedly restarted, the current of the device becomes more than 800 ua, and the same as the jlink download current; the software reset current...
Hi
I have been trying the various examples from the SDK with Keil V5.23. Some work, some require changes to IROM1 and IRAM1 before they will run Initially giving an error...
