Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Dear nordic,
I need a help to working nrf52840 dongle. It's not working when i press reset button led not flashing.
i don't know what happen to dongle can you help me...
Hi All, I am working on a problem for last 2 days and cannot find a solution, I tried everything and read many posts from others however nothing worked so far, either it seems...
So, another 2 hours down tonight converting to NRFX, this time it is trying to get the SPI to work.
This line -> static const nrfx_spi_t m_spi_master_0 = NRFX_SPI_INSTANCE...
Hi,
I'm trying to use twi and spi in the same project. But it results in this error:
.\_build\nrf52832_xxaa.axf: Error: L6200E: Symbol SPIM0_SPIS0_TWIM0_TWIS0_SPI0_TWI0_IRQHandler...
according to this article to modify my code. https://devzone.nordicsemi.com/f/nordic-q-a/27185/52810-how-to-use-dfu
It could be scanned but couldn't connected.
Is...
Hi Nordic support,
I have a nRF52840-Preview-DK. When I try to connect to nRF Connect on my Mac I get the following error: "Error while probing devices: Error occured when...
Hi Guys,
I hope that you could help me with issue which can be observed in my new "nRF52 setup". I've connect LSM9DS1 sensor to NRF52 DK. The "twi_scanner" example from...
Hi all. I use a STM32F103C8T6 as a transmitter and an Arduino Uno as a receiver. I cannot receive the value I am interested in. I have changed delay durations after each send...
Hi
I am using nRF5_SDK_15.1.0_a8c0c4d\examples\ble_peripheral\ble_app_uart & merged TWI sensor as well as nRF5_SDK_15.1.0_a8c0c4d\examples\peripheral\saadc. TWI works well...
Hello
If "NRF_ERROR_RESOURCES" occurs, does the set transmission data not be transmitted? Will it be sent partway? I do not know either.
If "NRF_ERROR_RESOURCES" is returned...
Hi,
I am working on Keyboard HID example application. I am trying to 'step into' the code (debugging) to understand the working of the code. But the example ends up in app_error_fault_handler...
Hi,
I'm trying to implement scroll buttons (not the up-down buttons) using buttons provided on the development board. The scroll buttons will scroll in left-right and up...
I am using nRF5_SDK_11.0.0-2.alpha_bc3f6a0 with PCA10040 and GCC. I am working on the ble hrs with DFU example. I have modify the hrs to my custom service with a 128bit service...
Hello DevZone,
I know that the subject has already be treat but in the others posts people seems to say that the error comes from the double buffering.
But in my case...
I am using the sensors LIS2DH12 and the BMP280 in my new design, both of which work on SPI. i will be using both the nrf51822 and the nrf52832 in separate designs with same...
