Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hello, I just wanted to share a problem I encountered and make some suggestions : I lost some time looking for a TWI problem while it was actually related to the pin reset...
Hello All,
I am using NRF51822 controller in my design.
I want to monitor battery voltage using ADC pin with voltage divider.
I have LIPO battery with 3.7V and 200mAH...
Hi Nordic Support, community,
After I flashed, the connectivity hex, ble_connectivity_s140_usb_hci_pca10059.hex from the SDK v15 downloaded after executing the patch on...
development software, with versions (SDKs, IDEs, SoftDevices, ...):
Computer platform, with versions (Windows/Linux/OSX, ...) Windows 10 Pro x64
hardware revisions (chip...
Hi,
I am trying to make a weather station with nRF52 feather and BME280. Currently I am making a measurement program. The base code is Custom:Heart Rate Monitor Example...
Hi friends I use nrf51822 with sdk12.3 version and I want to use infrared receiver.
What method should I use to write the infrared receiver code?
Also, does nrf51 have...
Hi,
I'm able to send arbitrary information to the host using generic HID descriptor (uses vendor defined page). There is no driver issue. I'm also able to connect to the...
I am currently downloading softdevice (S140) on our custom board using P19 connector on nRF52840 DK. Our custom board also has nRF52840. It seems the dsoftdevice is downloaded...
nRF52832 & nRF52810 don't support the Bluetooth 5 Range Extension (Coded PHY):
https://devzone.nordicsemi.com/f/nordic-q-a/39532/is-it-only-nrf52840-s140-which-support-bt5...
Whenever I deploy an example to the Fanstel BT840F with Segger ES, the S132 SoftDevice is always also deployed to it. I have attempted to change references to this in the...
Hi,
nrfx_uart.c has a bug where, once there is a RX error, the receiver gets stuck in a disabled state forever. This is because p_cb->rx_enabled is never set true, so the...
hi, my name is tyto I just learned programming about nrf52832, before I used to work with Arduino, after trying to learn nrf52832, it turned out to be very difficult for me...
Hi,
I'am using SDK v15.0.0 with the BLE OTA DFU bootloader. Is there a possibility to access the bootloader start address for a static assert in the application at compile...
We have bought nrf52 832 development kit.
When we checking the kit in nrf52 utility than it detects the IC nrf52 840 .
Hence we have erased all the memory in the DK...
Hi everyone,
I am using the following files to configure uart for laser distance sensor.
Serial Library
I am able to write command to the Laser sensor and also the laser...
