Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I'm unable to get any example code to test the timer in counter mode, I see the data sheet and trying to enable, but its not working can any one suggest me how to start the...
Hello,
I believe there is a documentatin error in document nan_40.pdf CIRCUIT BOARD GUIDELINES FOR aQFN PACKAGE.
Table 3 / Page 11
Hole size of blind via is mentioned...
Hi, I have some questions about GPIO interrupt.
Now, I want to know the state of the pin, So I use the gpio_pin_read(PIN) to get the state. But when the pin is suspended...
hi,
i am working on a project were i have to discover all the service on peripheral device and fetch data from it like nrf connect app.
so i am using nrf52832 with sdk...
Hi team
I have a problem that bothers me for days.
I try to run demo ble_app_uart_c with
NRF_SDH_BLE_CENTRAL_LINK_COUNT=8 and NRF_SDH_BLE_PERIPHERAL_LINK_COUNT=1...
I used to program my PCBs using the nrf52840 PDK, however, my mac no longer recognized the PDK. The PDK turns on and the application runs as LED 4 blinks but the LEDs next...
hi,
i am using ble_uart example to take time when data arrives and time when data being sent over bluetooth.
when i prints the time without connecting to bluetooth. then...
Board:custom board
Mesh SDK: V1.0.0
IDE:SEGGER Embedded
Problem a：
When I test the steps specified by “Interactive PyACI”, there is A certain probability of Provisioning...
Hello,
i asked this quastion once in this thread: https://devzone.nordicsemi.com/f/nordic-q-a/32444/reset-on_ble_connect-when-button-event I accepted the given answer but...
Hi Nordic Team, I'm trying to setup a gcc/eclipse based environment according to gustavovelascoh.wordpress.com/.../ on Linux/Ubuntu 16.04.1 64Bit. The Ubuntu system lives...
Hi, I would like to make an exact copy of the nRF51 dongle antenna (as was recommended by multiple blog posts by Nordic). I am concerned about the legal issues, and any IP...
I search GPIO pin bit definations and register. I saw pca10040.h GPIO defined.I dont know how to configurated P1DIR, P1EN, P1OUT etc.. I studied Texas Instrument before. I...
Hi,
I'm making my own prototype board using the nRF51822. this board is powered by a rechargeable battery lir2450 (3.6V): www.powerstream.com/.../Lir2450.pdf
i want...
Hello world
after several hours & day, Finally I have to implement this KNN code and nRF51822_adxl345 code. I have implement to one. but there is problem that..
I can...
I am trying to track down a fatal error and want to use the Error module as documented below, to get the line number and file name.
Using eclipse, where should DEBUG be...
