Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi,
I am having some trouble using fstorage to write data into flash. I want to store ~20 kB of sampled data before processing it, and I am storing it just below the bootloader...
Dear every one.
My company has ordered 20 development kit NRF52840 for our Mesh project. We will receive these board 1 week later.
But i have 1 preview development kit...
Could you please help me out on how to read my EMG sensor values and display it via the Nrf tool box. I have a redbear nano v2 and the digital output of the sensor is received...
Hello,
I'm having some issues with the MAXCNT limitation of 256bytes because I want to send larger packets and receive packets through the SPI Slave interface, which is...
I have an external board based on nRF51822 QFAC. I have a nRF52 preview DK. Will it be possible to detect my external board if connected via the preview DK. I tried and the...
Hello,
We've a Custom board based on nRF52832, it works fine in beacon mode using the Synth Clock (else it doesn't work):
// <o> CLOCK_CONFIG_LF_SRC - LF Clock Source...
When using the PPK to measure the current of our custom hardware the lowest range doesn't give logical results. (Either the PPK python GUI or nRF connect) When the nRF52 on...
Reference: nRF52840 DK Evaluation Board Schematics
The following inductors are lised in the schematic:
L1
3.9 nH
High frequency chip inductor ±5 %
0402 ...
I am working on windows xp command prompt and using nrfutil version 3.5.1
I want to do a Device Firmware Upgrade over BLE through my nRF52 DK board on a custom element....
Hi there,
SPIM3 running at max speed (32MHz) will be the fastest external interface (along with QSPI)
Because I would like to make to most of it, I wondered if you had...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hi,
Please help me on the nRF52840 UARTE RTS signal, through the doc: "nrf52840_ops_v0.5.pdf", we can know if we stop the UARTE RX by trigger the "NRF_UARTE_TASK_STOPRX...
Hi Sir,
I hope to add ble_nus and ble_nus_c into Central_and_Peripheral projects (ble_app_multirole_lesc and ble_app_hrs_rscs_relay), I use SDK 15.0.0 and nRF52832.
...
