Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I need to assign Rising edge and Falling edge event in a single pin.
I try to assign both Rising Edge and Falling Edge event into APP_EVENT_PIN.
There is a error...
Dear all,
I have noticed that NRF_LOG_FLUSH() function is used in many examples after each nrf_log print function. In some cases though, the program freezes when I try my...
HI!
nRF52832, SDK13
I need to know what happen with setted output RF power when peripherial devie connect to central device.
For example, if output RF power setted to...
Hi,
I am completely new to this technology. I am currently programming a custom board equipped with an nRF52832 based on the ble_app_uart example in the SDK 15.2 and is...
Hi!
24 days have passed since I was promised an update (which I hope will mean a solution), but nothing...
Also, there is no updated Getting Started Assistant and the...
Hi,
We are planning to use an Automotive Grade Bluetooth SoC in one of our new designs.
Some controllers in the nRF51 family seems to be Automotive Grade, but we also...
I tested with Light Switch Example in nrf5_SDK_for_Mesh_v3 version, I have set Transittion time to 160 second and Delay to 0, problem occur is the device Cann't countdown...
Hi,
I am using an nrf52840 MCU, Nordic SDK 16.0.0 and IAR Workbench for ARM v8.40.1.
The MCU has the following configuration:
- MBR installed
- DFU secure bootloader...
Hello everyone,
I faced with bus fault after running beacon example from mesh_sdk. It occurred after calling mesh_provisionee_prov_start().
Unfortunately, I didn't found...
Greetings...
Provisioning w/ Android tool only works when board is connected to debugger.
Provisioning failed to even find the devices when scanning after disconnected...
When enabling 3 instances of SPIM (1,2,3) on NRF52840 the application doesn't start at all.
Weirdly however, the application works fine when SPI3 takes SPIM3 and the rest...
Hi,
Does SoftDevices v7.0.1 supports Multiple Advertising Sets feature? I read that Softdevice v6.1.0 does not support the Multiple Advertising Sets feature. Let me know...
Hi. I was wondering if maybe you know where can I find the PCB desing of any of this modules: NRF24L01+ (the black one) or the SMD version. I only can find those pictures...
Hi gays,
Now, I want to c ollect a pulse waveform(example : 1s, 50% duty cycle ) which accuracy requires milliseconds resolution and I use PPI to read a capture value from...
