Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I would like to program the NRF52810 with the SoftDevice 132 and my bluetooth program. Is there any way to reprogram the NRF52810 over bluetooth rather than using a wired...
Hi,
I'm wonder is the speed of i2c on nrf52832 can be faster then 400kbps? even use EasyDMA, the speed still can't faster then 400kbps? I also look into the max speed of...
Hello All,
I am a bit confused with the maximum speed that is achievable with the USBD CDC ACM driver.
In Previous threads like this:
https://devzone.nordicsemi.com...
I developed a functioning application that advertises with Nordic UART Service, connects to a smartphone application, then reads various sensor data using the SAADC and transmits...
Hi,
I have read all around DevZone that more details about AoA/AoD based direction-finding feature were expected to be released around Q4 of this year. This is very exciting...
Hi,
I am using nRF51822, and try to use the ECB block AES128 to do some data decryption.
From the SDK I found 2 API functions:
uint32_t sd_ecb_block_encrypt ...
How can I generate two complimentary signals using PWM with a period of 3.33us (300khz) with ability to control number of pulses to generate.
1: With current api PWM takes...
Hello,
I have tested and verified the code for my application on the NRF52 DK, but now I need to program my own custom device using the nRF52832 chip. I saw there was a...
Some bugs in ble_app_hrs_freertos example from the SDK when handling buttons: (at the end of this listing are same tests but with ble_app_hrs (no rtos) and buttons are handled...
Hi, We are working on Thingy91(nRF9160-pca20035). When thingy91 connected to system through USB, We getting BLE UUID values through nRF52840 on nRF9160(on nRF Cloud also)...
Hello,
I am porting a software to the nRF52 SDK16.0 . This software uses Floating Point numbers with Exponent-Byte=0x7F to signal Error conditions (then treated as unsigned...
Hi. I want to evaluate the current consumption of the nrf9160 module (I have a Thingy91) and I want to disable all logging functions. I started with the mqtt_simple example...
I have a characteristic with variable length and max length of
NRF_SDH_BLE_GATT_MAX_MTU_SIZE - 3
i.e. the max possible data length based on the max MTU.
During connection...
My Thingy:91 was added to nRF Cloud using "+" > "LTE Device" and then "Already have an active SIM? Skip this step" (iBASIS roaming doesn't work properly in Switzerland so...
