Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi,
I was working with the SPI interface of nrf52DK microcontroller boards and wanted to know if there is a way to change the timings of the low and high levels of the Slave...
I'm designing a solution based on a series of nodes that senses data and has to send it wirelessly to a hub. Each hub must be able to receive data from about 4 to 8 nodes...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
Please tell me the operation when garbage collection is executed. The setting values of FDS are shown below for reference.
We...
nrf52832 master wakes up the slave under sleep?nrf52832 slave wakes up the host under sleep?
My boss wants very low power consumption. I think the host can wake up the slaves...
Hi,
When I used the same command, I was only able to read the 5 bytes correctly. The Most higher byte does not match.
C:\Program Files\Nordic Semiconductor\nrf-command...
Hi
I would like to know if it is possible to to run the Nrf905 chips on 5v logic level without damaging the chip ? i see many people playing with arduino and these chips...
Hi, my customized board was using nRF52840 with 15.3 ver SDK.
And we want to make the DFU download process part can progress in the application.
(such as background download...
Hi Sir
I have used sdk 11.0.0 to develop my bluetooth application but i am facing some issue, so want enable debug logs, but i am not getting where to enable it plz help...
Hi!
I'm interested in trying out hci_usb sample of nRF Connect SDK with Nordic's Link Layer.
With following changes to application configuration I'm able to compile the...
Hi there,
I am trying the asset tracker example on nrf9160DK-HW 0.9.0.
While I have been able to get GPS fix within 20-30 seconds using the "GPS sample" example... I've...
Hello, I am starting to upload my code to some new Raytac MDBT40 modules, and am starting with the soft device of course.
I am using uVision V5.28.0.0
I can not upload...
We have devices that we want to turn on at some future date. This means that when they're deployed they should somehow get real time, calculate when they will wake up, and...
I am seeing that the default manufacturer BLE is defaultly F5:41:36, received experimentally from inspecting data from the nRF52832... Now, of course there is sd_ble_gap_address_set...
Hi,
I have a custom Nrf52810 board. It was working fine and was advertising well. Somehow ble chip got damaged and I needed to replace it.
After I replaced, I can do debug...
I would like to use Uart with low standby power consumption. and I have read this post which recommend to use libuarte:
https://devzone.nordicsemi.com/f/nordic-q-a/53880...
