Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
nRF51822 PS says standard drive GPIO output voltage will be VDD-0.3V ~ VDD In our previous project w/ nRF51822, I found it to be very close to VDD when connected to GND via...
Hi... i am using nRF52832 ,15.2 version sdk . I want to send the data from esp32 to nRF52832 through Rx ,Tx . I have done connections rx,tx,gnd . I can able to transmit the...
Hello,
I'm trying to setup an automated pairing for two devices. My peripheral device is advertising and should only allow connection requests from a specific central device...
I'm developing a multirole device to connect to a peripheral device that we developed earlier.
The multirole device when acting as a central device it scans for the peripheral...
To the kind attention of Nordic support team,
1. I have been using secured gazell library, where master is always polling in order to receive a message.
I was wondering...
Hi!
I'm developing a TCP server running on th e nRF9160, but there seem to be a problem with accepting clients. The code is very simple, just calls to socket, bind, listen...
Hi. I've developed a PCB with nRF52832 and I'm having problems with the circuit. When I put my hands closelly of P0.00(XL1) and P0.01(XL2) the bahavior of nRF changes... I...
I apologize if this was already answered elsewhere - I didn't find it.
I have been digging in the nRF52840 source code for the serial_nRF52840 SES project to understand...
Hello, I am trying to switch from BLE_GAP_PHY_AUTO to BLE_GAP_PHY_CODED in runtime, and I need to change central event length via sd_ble_cfg_set(). Whether is it possible...
Hi, i am working on servo motor using nrf52840 development kit , i want to run parallely four servo motors , i have merged the ble_app_uart+pwm library example ,
1. As of...
Hi,
I am using an external RCT module to provide 32.768kHz square wave for the nRF52832 instead of an external crystal oscillator. When the system goes to deep sleep mode...
Hello,
I'm aiming for flashing the nrf52832 via SWD via my own SWD implementation.
I'm good so far with the init phase, reading IDCODE writing registers. Long stort short...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
I modified ble_app_blinky with below...
I am getting ecg data from max30003 IC which i want to send via BLE to and application. I have the Ble code working on its own and the SPI code to get ecg data working on...
