How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hi,
I have searched Devzone for changing the transmission power; even though there were similar issues related to mine but at the end, It did not help me.
I am evaluating...
Hello
I am reading sensor and broadcasting via nrf51DK its working perfectly when voltage supply is morethen 3v
but when I give voltage between 2.1v to 3v its stop broadcasting...
I cannot install the app "Programmer" automatically. The connection always fails due to poor network in our country. The error report is as follows:
Is there anyway to...
Hi Community,
printf() (and variants) fail on rounding floats: This is is probably an error in the printf implementation. I tested it with SDK 16.0 on NRF52840.
Format...
Hi,
In addition to listening the advertiser's and beacon data we also need to offer the master application - which is connected to BLE-module via UART - the possibility...
Questions about ‘Application data’ placement in the flash memory
Is there a function or other mean that could give me what is the lowest flash memory address that is occupied...
Hello All,
I am working on the Nrf52810 with sdk 15.3.
When we connect device through nrf connect app (android) i wanted to disconnect after 1 min .
I have given timer...
nRF52840 DK:
ble_app_blinky is working. After that, I flash ble_app_bms, ( working),
then flash ble_app_blinky- the smart phone is not able to discover service .
Any...
When scanning 1MBPS & Coded PHY at the same time, the probability of Coded PHY broadcast scanning is very low, and 1MBPS PHY broadcast can be scanned normally Slave configuration...
i have come across a couple posts related to providing more compatible Altium design files so that other CAD packages can import them. The best articulation of this point...
Hello I have upgrade software and modem firmware and the program using mqtt protocol don't work any more.
Besides the connection to the broker (many error -106), the program...
Hi, Im using a BMD-300 board with the external crystal installed, I can run zigbee examples fine, even using the external crystal, but when running the Mesh examples I can...
Hi
I have some doubts about NB-IoT and I wanted to clarify them before start deeping developing with nRF91 since this module work with this network.
I know that NB-IoT...
Hi,
I use SDK13.1 FDS example and have some questions about that.
Is there any influence about the lifetime of Flash when i use FDS function to write and delete the records...
Hi,
I am a beginner with nrf9160 DK and followed the instruction in https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_programming.html#gs-programming...
