I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hello,
I have tested and verified the code for my application on the NRF52 DK, but now I need to program my own custom device using the nRF52832 chip. I saw there was a...
Some bugs in ble_app_hrs_freertos example from the SDK when handling buttons: (at the end of this listing are same tests but with ble_app_hrs (no rtos) and buttons are handled...
Hi, We are working on Thingy91(nRF9160-pca20035). When thingy91 connected to system through USB, We getting BLE UUID values through nRF52840 on nRF9160(on nRF Cloud also)...
Hello,
I am porting a software to the nRF52 SDK16.0 . This software uses Floating Point numbers with Exponent-Byte=0x7F to signal Error conditions (then treated as unsigned...
Hi. I want to evaluate the current consumption of the nrf9160 module (I have a Thingy91) and I want to disable all logging functions. I started with the mqtt_simple example...
I have a characteristic with variable length and max length of
NRF_SDH_BLE_GATT_MAX_MTU_SIZE - 3
i.e. the max possible data length based on the max MTU.
During connection...
My Thingy:91 was added to nRF Cloud using "+" > "LTE Device" and then "Already have an active SIM? Skip this step" (iBASIS roaming doesn't work properly in Switzerland so...
I've been trying to get the MQTT simple sample started however after changing the hostname to "mqtt.eclipse.org" and running the sample, it stops with this error. Please how...
Hello, I am using NRF51822. I want to run UART communication on two different baud rates for 2 different hardware on pin number P09(TX) and P11(RX) respectively. I have to...
The queued writes library provides AUTH and EXECUTE events, but I think it also needs a CANCEL event.
In my code, when I receive an AUTH event I obtain the data buffer using...
Hi,
I got a brand new nRF916 DK. I updated the modem firmware to mfw_nrf9160_1.1.0 and updated the application firmware Asset tracker with nrf9160dk_asset_tracker_nbiot_legacy_pco_2019...
I have set up a PA / LNA and watched the radio details.
When the connection interval was 50ms, it was confirmed that the device was communicating every 50ms.
Look at...
Hello
I want to program and debug NRF52840 dongle using jlink But the jlink is not able to find the target . i am using SEGGER J-Link Commander V6.60d application for flashing...
