Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello!
I am working on firmware for device that has freertos in the base and implements BLE beacon and 1 service with 7 characteristics. Everything works. But power consumption...
Hi,
We are currently testing DFU upgrades on Android. In my current setup I have two different phones, a Sony one running Android 8 and a OnePlus running Android 10.
The...
We have a device (in central mode) initiating a secure connection to a peripheral (slave) via the usage of `pm_conn_secure(conn_handle, false)`. This results in a `PM_EVT_CONN_SEC_SUCCEEDED...
Hi All,
I want to convert analog input into digital using SAADC on nRF52840 DK. After that to push the SAADC output through the Bluetooth (nRF connect bluetooth mobile application...
Hi，
Recently，i try to install the tool chain of nrf connect sdk as the instruction as guide。After installed west，then run command “west update”，but got an error：
Can...
Hi ... folks
I am using nRF52832 and analog IR sensor , Working with the example saadc . In this case , i am giving the IR sensor input voltage as 5v , analog pin 2 .I am...
Hi,
I am using NRF52832 Development board, SDK(nRF5_SDK_15.3.0_59ac345) from this i am using (/nRF5_SDK_15.3.0_59ac345 (4)/examples/ble_peripheral/ble_app_uart) example...
Is the nRF52 RSSI block of the RADIO module based on the entire 2.4GHz ISM band, or can it be configured to only measure a given 1-2MHz band of interest? According to the...
I'm using the serial library for the first time. What are the advantages/disadvantages of using IRQ and DMA? How should FIFO queue and buffer sizes be chosen?
Hi,
I am using the following code to implement a millisecond timer read function. In main, while loop, I do nothing but run a 1ms delay and measure the time in mill second...
Hello, I'm a researcher.
I wanna use Bluetooth CTE(Constant Tone Extension) feature with 1-antenna TX + 1-antenna RX.
I have seen some articles that nRF52840 DK does...
I am using nRF52832 with SDK 16.0.0. I have a simple application that uses SAADC and BLE. It reads values from three channels AIN0, AIN2 and AIN4 and sends them via BLE every...
hi all,
we're developping an application to control the frequency and the duty cycle of a pwm signal throuth ble .
firstly we have built both the functionalities separatly...
So, this library in the SDK looks pretty much exactly what I'm looking for. basic data record storage functionality with a focus on safe record writing under battery power...
