I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
Hello!
I currently want to save the sensor data obtained by SPI communication to the microSDHC card by SPI communication.
Writing to the SDHC card is possible without...
To the kind attention of Nordic support team,
I'd like to open a new thread after the first one ( https://devzone.nordicsemi.com/f/nordic-q-a/46318/configuration-of-gzp_dynamic_pairing...
I have been using Power Profiler Kit nRF6707 for awhile without problem.I made a mistake by downloading firmware when the PPK is attached to nRF52 DK, the software on the...
Hi all
The iC is not advertising , neither it is able to get programmed.
The voltage levels are ok. It is getting sufficient Voltage at its o/p and delivering o/p at DEC...
Hi,
Please help to share Memory size of following SoftDevices:
S112
S113
S132
S140
Also, what will be the memory size of SoftDevice if i implement Central +...
Hi,
We are migrating from 12.3 SDK version to 15.3 version.
We observed the almost 22 KB of RAM is reserved. Where as in 12.3SD version we don't see this.
We are still...
Hi,
our company one new product using you nRF52832. We already prepared everything for CE (RED ) and FCC certification process. Only thing that is unclear is Bluetooth SIG...
Hi!
I am currently using SEGGER Embedded Studio version 4.12, nRF5 SDK version 15.2.0, nRF5 SDK for Mesh version 3.1.0, Hardware BMD-300 Evaluation Board.
i using the...
I need to measure a load-cell bridge. Although, I'm fairly certain I'd be better off with an external delta-sigma ADC with an internal amplifier - I'd like to run through...
Hi,
I study on Thread resently.
I found it is not any output in the Debug Terminal Window when using NRF_LOG_XXX, but the J-link Control panel showed the logs.
Here...
Hi,
I am trying USB DFU trigger.
I have connected GPIO P024 to Reset port P018.
Bootloader is also programmed.
When I use nRF connect/programmer.
It's always waiting...
My system: MacBook Air with macOS 10.14.6, Xcode 10.3, with sdk at /Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX10.14.sdk
When...
Dear nRF52832 experts,
I have a SPI slave device which can periodically notify the MCU with data ready (DRDY) signal. For each DRDY signal, we should perform a SPI transaction...
