Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello,
I've been trying to test DFU over UART which has been added in SDK13.1 but after following every resource I've found I always end up with DFU not working
The...
I found this question which partially answered what I am looking for:
devzone.nordicsemi.com/.../
Essentially, if I am creating a new project with my main.c file and...
Hi I am trying to design a custom BLE board using NRF52832 by following the reference layout.
I am new to RF design and I have got a few questions that I would really appreciate...
Hi
I'm trying to implement DFU in my project. So far, after I sending 01-04 to the control point characteristic(1531)，I can get bootloader signal, to be exactly, i can enter...
Hi,
Can we interface a smbus based sensor with NRF51 or NRF52? The only difference between smbus and TWI is the minimum speed requirement which is 10Khz if I am correct...
Dearl all,
I want use the eclipse and gcc together to program the board nRF52840 Preview DK. I was following the tutorial devzone.nordicsemi.com/.../.
I followed the...
Hi,
I'm using nRF52832 with sdk 13.0.0(softdevice 4.0.2).
I had trouble to connect nRF52 and some android 7.0(or upper version) smart device.
I tested samsung galaxy tap...
Hi All,
I am trying to get the serial DFU working with nRF52832 development kit with SDK 13. I am able to get the bootloader flashed and have installed the nrfUtil tool...
since im working on sdk9... advertising program(hello world).i wanted to generate a random address .but i couldnot complete it sucessfully.can you please help me in providing...
Hi
I'm trying to create a DFU package for a SDK11 (insecure) DFU
For just the bootloader I have this syntax in my makefile
nrfutil dfu genpkg --bootloader $(OUTPUT_BINARY_DIRECTORY...
Hello all,
I started working with nrf51 series on mesh networking as i am new to this i want know whether the chipsets will come with preadressed? as it require to adress...
Hello,
recently I was going through this and the following statement concerns me:
First of all make sure you have a
recent Linux kernel installed (at
least 4...
Hi,
I have serious troubles when trying to program the board with softdevice (s140).
nRFGo Studio:
nRFGo Studio installed and running fine. When I connected the board...
Hello!
I'm using this module and I currently am working with keil. I would like to switch to Segger but the documentation for this module is only for keil from this manual...
