Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I am using ble-sniffer_nRF51822_1.0.1_1111_Sniffer.hex as the sniffer and I am trying to see all ble beacons.
Because I have many beacons about (100 in one second...
Hi.
In SDK 14.0 examples, there are two examples for pwm.
I analyzed both example.
pwm driver example source looks like that it use pwm peripheral driver source.
And...
Hello,
I would like to sample the battery level of my nrf52832 DK and send it through BLE. I have started from the example ble_app_hrs for SDK12.2 since the service was...
Hi,
Most of the sections of my application are functioning as I want it to, except these two (step 3 and step 4).
Application:
Connect device (with Auto connect...
I noticed while running a Bluetooth scanner app on my iPad, while testing one of my devices, that it was showing someone else's device in the locality.
What I found strange...
Hello!
I have:
nRF52840-Preview-DK (pca10056)
nRF5_SDK_13.0.0_04a0bfd (s140)
I load **nRF5_SDK_13.0.0_04a0bfd\examples\ble_central\ble_app_uart_c\hex\ble_app_uart_c_pca10056_s140...
I have an interrupt coming in every 50-150 microsecs and I want to measure these intervals as precisely as possible.
I tried this with SDK12.2:
APP_TIMER_INIT(0, 5,...
We're trying to bit-bang SWD to program an nRF52832, and we're running into some problems getting the nRF52 to respond. One theory is we're not generating a high enough clock...
i just purchased the www.xcluma.com/bluetooth-4-0-module-NRF51822-2-4G-module-development-board-ble-4-0 this xcluma nrf51822 module , so how can i progarmme it . which IDE...
Hello,
I've noticed the following sentence in s132_nrf52_3.x.x release notes:
"Synthesized low frequency clock source is not tested or intended for use with the BLE...
I'm following the tutorial in the NRF52840 SDK on setting up a Thread Border Router here and I've run into some issues during testing. For one, I'm trying to resolve ipv4...
