Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I would like to know the best practices to update a passkey for bonding.
For the moment, I have a static passkey that I set during ble initialization and I can...
To start off here, I'm using a Laird DVK-BL652-1.0, which according to Laird only needs to be re-configured to use the internal oscillator, but is otherwise very similar to...
Folks,
Have been using Keil MDK Lite in the past, in a Win VM. Larger code (over 32KB) plus the convenience of running without a VM layer have led me to switch to NetBeans...
Hi,
I want to use the AES-CCM of nRF52832. But it can not work with the softdivice.
I have read the following question and answer.
devzone.nordicsemi.com/.../
It seems...
Hi Nordic folks,
We are developing a product using nRF52832 with a Power Amplifier (RFX2401C) for extended range. For communication we are using ESB with some modifications...
I was redefining the init packet and when it came time to generate the nano-pb files, it looks like there is a fair amount of difference in the newly auto generated pb.c and...
Sorry if these questions are discussed already. I'm a newbie to Bluetooth project. Let me explain in brief. I have a central and peripheral device. I am transmitting 10samples...
After quite a few difficulties getting Keilv5 to work with the included examples with no responses ( devzone.nordicsemi.com/.../) I decided to give Eclipse a shot.
This...
Good day All,
We are in the process off procuring a project using nRF52, and I need to find out some important things. Are there any costs in using any of the libraries...
I am using nrf52840 module(peripheral) for transmitting 10samples/10ms and central device as the same nrf52840 for receiving the samples. Although I receive the packets, there...
Hello,
I'm working on an application in which I have to dynamically switch between a TWI master peripheral and SPI master peripheral that use the same peripheral ID (our...
I have an NRF24LE1 transmitter using ESB. It is sending a static payload of 10 bytes every sec.
The other configurations on the transmitter are: RF channel:2, CRC: 1 byte...
Hi,
i'm wondering if there is any IC (for example nRF52832) that can reach a range up to 155 meters available within the Nordic semiconductor catalog ?
i know that the...
In nRF5 SDK 12.1.0 a bug was fixed in nrf_drv_wdt_init(). Watchdog timeout could not be larger than 131 seconds because of (x * 32768) multiplication before. This bug is again...
In the spec it says that the typical ramp up time is 140us (or 40us in fast mode). But there is no details on maximum or minimum. What is the true tolerance on this value...
