Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Where could i get the apk of thingy 52? it's hard for me to log on the Google play to install it because my phone didn't have GoogleServicesFramework, could anybody send me...
I am working on RTLS project. In beacon i am advertising battery life and temperature along with minor number and RSSI . I am merging battery strength and temperature in major...
Hi!
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
* android ver.8 smartphone with nRF Connect
I have implemented the...
Hello I'm using a macbookPro 2016 which only has usb-c and I can only connect the dk through a usb hub.
I have already installed the nrf5x-Command Line Tools for OSX but...
Hello everyone, i'm currently doing a project with nrf52832 and i just came across a problem. I configured 3 pins as output, then i set 2 pins to high and 1 pin to low. But...
I would like to implement UARTE.
· Nrf 52 · SDK15 · S 132
The big advantage of EasyDMA is that it does not issue interrupts for each byte received. In nrf 51, "app_uart_get...
Dear Sir/Madam,
Normally battery level notification is only one byte. But I need send byte array of 58 bytes through battery level notifications in my project. I have to...
I am developing my code in a custom nrf52832 breakout board. My code was modified from the example "ble_app_uart".
I find a high current issue with UART. The current is...
Hello,
I am trying to evaluate the NRF52832 on a custom board and i will design the antenna according to your NRF52 Thingy:52 design. I am quite a newbie about RF&Antennas...
Hello
I'm using SDK 15, S132 PCA10040
I have followed this tut.
I've tried 2 scenarios which in both I get error value:
1. when advertising_init() is before services_init...
Hello,
I saw this , but I was struggling with the merge for quite a long time now. Is there any ready example for e.g. provisionee or provisioner from light_switch merged...
Hi, Nordic!
I wanna know how change characteristic(service,Rx,Tx) UUIDs .
For example,
Proximity UUID : 01020304 -0506-0708-0910-111213141516
Service UUID : 01020304...
Hi,
I'm trying to merge central/peripheral example "ble_app_hrs_rscs_relay" with "ble_app_buttonless_dfu", and get error while compiling ‘ble_dfu_unbonded.c’:
I've included...
Hello I originally wanted to use esb_ptx/esb_prx but the packet could not be changed to 128 bytes! Compressing data packets is inconvenient! I use radio to achieve my project...
