NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
Hello,
I am searching for a provisioning API for the nrf52832 to develop an application for Android and IOS. My preference is one that already can work with Googles flutter...
hello:
our hardware engineer had designed PCB,it can't reach more than 100m..howerer the nrf52840 DK can reach 300 or more meter.
so is there any people can support some...
When using nrfutil to generate a DFU settings page (with backup page) of settings version 2, the .hex-file generated by nrfutil is not word-aligned, i.e. the number of bytes...
I noticed that as of SDK v16 a required component to use the Soft Device is nrf_section_iter which is located in the directory "\libraries\experimental_section_vars". Is this...
Hello,
The product specification for the nRF52832 only shows 3.0V performance. What is the performance in parameters such as Tx power, Rx sensitivity, maximum MCU clocking...
Hi,
I'm currently developing firmware in the Arduino environment using a dev board (Adafruit Feather nRF52840). Once I complete development, how do I transition the firmware...
Hi, I am developing the application in nRF52832 with SDK_16 in SES.
I have a problem with DFU
I need to run the application and DFU has to be activate only if the mobile...
Hello everyone
I'm using NRF MESH4.0, I have add simple_on_off model to experimental_dimming example,and it works .
My question is : MESH PROFILE V1.0 have mentioned bound...
Hello, i am trying to adapt DFU in the Light switch Proxy server example, however in midle the process of receive the DFU packets i got this error: Abort event. packet loss...
Has anyone (tried to) simultaneously use the same QSPI Flash memory directly from an nRF52840 program and as a USB block device?
We have both functions running in the same...
Hi
I am working with nRF52832 DK, using Segger IDE. I want to read data(a file) from a computer and process the data on DK. Is there any way of doing it? Also, is it possible...
Hi Nordic Team:
Can you help me to support BIS or CIS example .btt file。This file was captured by Ellisys tool。So ,I can refer to file ，and understand 5.2 Core Spec about...
Referencing the recommended 52840 PCB layout for the WLCSP package, we noticed two thru-hole vias in the middle of the ground area (in the center of the package). Do these...
Hello,
I am trying to implement ble DFU on our custom nRF52832 board. Up until now we have had no issues with our application running as SoftDevice+Application but some...
