Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Our company is in the process of developing a new IoT product for LTE-M and NB-IoT. The sample application lwm2m_client runs fine on our devkits nRF9151DK & Thingy91 and connects...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hi
I am trying to mugrate my app from v2.6.1 to v.3.0.2.
As I have several configuration variants, so I build from batchfiles, ending in a west build command. Updating...
Hello, we've a nRF9161 DK board a we saw on the back side a footprint for mounting an SD card holder and we found the SD card holder component in the BOM.
Unfortunately...
Hi,
I am currently developing an nRF54L15 module.
During the evaluation, I measured the Tx current consumption and got a result that was 2mA higher than the value listed...
I can flash the chip. I can run the debugger. I can go to the connected devices, select the device, go to the little "plug" symbol on the RTT, and select it. That brings up...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
Hello!
I'm taking some performance metrics for encrypting data on my nRF52840 device and I was wondering if you might be able to help me. The goal is to see how long and...
Why project config is not finding relative path of these files but absolute path works fine:
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip-DAC-Cert.der" ...
Hello,
Does the nrf_oberon library support the nRF54L series parts? In the technical documentation, it appears that M33 parts are supported: https://docs.nordicsemi.com...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
I’m writing this post because I’m experiencing a problem with data transmission between two devices—a sensor and a USB dongle connected to a PC—each equipped with a Minew...
We are in the process of finalizing the RF transceiver chip for custom protocol development.
Please suggest the suitable chip and any reference implementations available...
Hello,
I´m trying to measure the current consumption on the nRF54L15-DK Rev. 0.9.2.
There are a few questions:
1) What is the role / purpose of the voltage buffer? ...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
