Hi,
I want to use nPM1300EK、nPM PowerUP (official v2.1.1) profiling a chargeable battery, whose rated capacity、standard charging current is 2000mAh and 400mA respectively...
Hello,
I'm developing my custom sensor application. It's a matter over thread device. Before final product I'm working on a NRF52840 DK PCA 100056 v3.0.1 and NCS 3.02. It...
Hello!!
When I'm reading carefully about the nRF7002 Power save operations, It's hard to understand about Power save Exit Strategy.
https://docs.nordicsemi.com/bundle...
Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
Dear devzone, Can our nRF52840 detect 20 nanosecond voltage fluctuations using COMP? For example, if I set a lower threshold of 20mV and an upper threshold of 60mV, and the...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hello,
is there a good documenation or introduction about the Programmable Peripheral Interconnect Feature? I read the short part in the Objective Product Specification...
Hi everyone,
I need to use an nRF51822 (MBH7BLZ07-109033) mounted on a custom board.
I want to develop my firmware application on the custom board in such a way I can...
Hello,
I am using nrf51822 doing projects. I met an issuse which is that at the first 6 minutes, it can normaly go into UART interrupt and run subroutine successfully....
I'm testing out TWI on pins 24/25 and I get a crash when I attempt to do a TWI transfer and I find myself in: WDT_IRQHandler ()
I'm using much of the example code:
APP_TWI_INIT...
Hello, I have a few nRF devices, and I am unsure as to which revision the ICs are. Here are the three HWIDs:
0x00AE,
0x0086, and
0x0077
I tried looking into the nRF51_Series_Compatibility_Matrix_v2...
Hi,
I need to sample 2 inputs at 200Hz and send it on an app. Can I send the data at this speed using UART service? I was trying to do it using HRM example but could not...
Hi, I am trying to compile the code
github.com/.../main.c.
I need to include the header file uart_confg.h, can someone tell me where I can find it in the sdk 10 component...
Hi,
I wrote a program that uses ESB communication between two nodes. On both sides I use the same ESB configuration and the same ESB init function, the difference is only...
Hello,
Environment: nRF51DK + SDK8
We've developed the beacon application but the advertising interval is set to 5 seconds. The beacon can be discovered by nRF Connect...
I have searched here on the DevZone, and also around the web, and don't see this issue mentioned elsewhere. I really appreciate any help finding a solution.
I tried following...
Hi All,
I think I noticed a bug in the nRF Connect v1.0 application. The Scan Response data is not shown in the Windows application. When I scan the device with the iPhone...
nRF8001_BLE_UART.txt
I am using an NRF8001 with the ble_uart_project_with_dfu_template and programmed an ATMEGA328P with it. The code works great and I can scan and communicate...
Dear sir,
Can we use 8.08.90 J-LINK EDU for programming of Nrf52832 Chipset.Please also specify its limitation if it has any.
If we cannot use this then please specify...
