Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi.
I have a custom board based on the nRF51822. Application uses s130, SDK 11.0.0. It's a peripheral. Using gcc.
I'm finding that when field testing my device, it will...
Hello,
I'm trying to measure the time difference between two pulses using GPIOTE, PPI and a Timer.
My platform is:
nRF52832
SoftDevice S132 v2.0
My thinking is to...
without timer it work fine but when i use timer it goes here.
my timer code is this
#define APP_TIMER_PRESCALER 0 /**< Value of the RTC1 PRESCALER register. */
#define...
Hi,
I am following the user guide nRF51822 Evaluation Kit User Guide v1.2 , the heart rate monitor demo, Scaning for available Bluetooth low energy devices:
I started the...
Hi,
i am working on a custom board with nRF51422. I can program this board with the nRF51-DK. I use ADC and a temperature sensor via I2C. Everything work well but actually...
I am using nrf_toolbox on Windows Phone 8.1 and PCA10040 development board. I loaded the uart example and with my phone I can send text via nrf_toolbox. But when I want to...
Im' trying to send a set of 80 bytes using indication. for that I have a characteristic sending each time 20 bytes and wait for indication acknowledgement before sending the...
Hello Nordic! My application requires an nRF51822 using S110 to handle both Notifications and Indications over the same characteristic.
The CCCD value 0x01 = 0b01 enables...
Hi,
In order to start my own board with nRF52 component throught SWD, I think I've to use Segger Jlink. I expect to buy the basic version, that sound good for me, but I...
Hi,
I have some problems with bootloader debugging by using app_trace_log().
My board is pca10028, and I use the SDK 10.0.0 for it. The Keil version is v5.20 and Jlink...
Hello All,
How to interface nRF905 with nRF51DK board?
Any driver is available for nRF905 which support nRF51.
Any help will be appreciated.
Regards,
Rajneesh
Hi,
I'm using PCA10028 to communicate with ADS1131 ( www.ti.com/.../ADS1131) which outputs 18bit on SPI bus. I managed to get the data out by reading 24bits, but it feels...
Hello ! When I make a read with the SPI from a sensor's register the data sometimes comes correct and most of the time wrong. I tested the read operation with an Arduino and...
Hi
what is the best way to implement a sleep after disconnect?
We are using a custom board and I implemented it this way:
on connect : turn advertisement off
on disconnect...
