Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
hello,
Please forgive me if I am asking a stupid question.
I was editing S130 demo app and I included pstorage.c file to the project. while compiling it is showing error...
I have compiled my mbed program and hex file has been downloaded but I am unable to drag and drop my hex file to mbed USB drive. It is saying Not Ejected properly. I tried...
I am following app note nAN-29 "nRF51 Development with GCC and Eclipse Application Note v1.1". In the section "Flash download" there is mention of an executable called nrfjprog...
Hi
I use the PORT EVENT to produce multiple interrupts.But I have a question by these:
NRF_GPIO->PIN_CNF[BUTTON1] =
(GPIO_PIN_CNF_SENSE_Low << GPIO_PIN_CNF_SENSE_Pos...
Hi,
have some of you expierence with profiling on a nrf51422? I think what would be nessesary, is at least one high priority timer, to sample the program counter, some kind...
Hi,
I’ trying to save some user configuration data on the NRF51822 Flash using pstorage module.
Below is the code that I wrote, the code runs on the board with no error...
I have two boards based on nRF51822 parts:
Nordic dev kit PCA10005 Rev 2.2.0 2014.14, chip marked N51822-QFAAG0-1351AG
Custom board with Fujitsu MBH7BLZ02-109004...
I'm getting an error which says the identifier ble_temperature_t is undefined, and it is showing as an error in the keil (unkown type name). However when I click on the variable...
Hi everybody,
I just received the nRF51822 EK and as I was starting to set it up I ran into this. It took me a while to figure it out but when trying lo load the blinky...
Hello,
I have problems with project making since I started with KEIL uVision 5 (in uVision 4 I had no problems, but see no way to download uVision 4 any more).
I followed...
I am not seeing the nRF51822 as an option when I go to select a target device in Keil µVision.
From reading questions on here I understand that the nRF51 SDK should include...
Hello,
I'm new to the nRF51 modules and I just started with nRF51422 module.
I have Keil uVision v5.11.1.0 with MDK Pro v5.11.0.
I have installed nRF SDK - nrf51_sdk_v5_2_0_39364...
