Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
In s210 there are functions sd_flash_page_erase, sd_flash_protect, and sd_flash_write. There is no sd_flash_read.
How do I read from flash? I can write to is using sd_flash_write...
Hi
I just want to create a custom service with a characteristic, which sends "n" (upto 200) bytes at same time and this bytes are are written to a SD card via SPI
So...
Hi, I have been using the nRF8001 Arduino SDK with nRF8001 chip. I wanted to set the data for the different services I'm using and thought I would go ahead and use the services...
Dear sir
Now, I am trying multi-link examples at SDK5.2.0 S120 example. I found s120 central only can receive one byte data from s110 multi-link peripheral. Could we modify...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hello,
I have some problem with NRF24L01+. I'm trying to make bidirectional connection between two devices with this chip. When I'm sending payload with ACK, TX_DS interrupt...
Dear nRF Gurus,
I made a board with nRF8001 and PIC24F to stream some sensor data to a computer. I have also developed a simple Mac app to communicate with my board. (similar...
Hello,
I am redoing some experiments with 2 pca10001 and the ble_hrs example (with s110, s120) !
What I would like to do is that the s120 side displays the power received...
I'm designing a small board with an nRF51822. I'd like to use a 'meander' PCB antenna similar to the ones on the Evaluation Kit and 'dongle'. Is there a definitive guide ...
I'm trying without much success to write something fairly simple. Basically connect a signal to a pin, and run a function whenever that pin changes state. What's confusing...
Hello all,
I am debugging my nrf51822 application using evaluation board and keil debugger. I have uncommented the ble_debug_assert_handler in app_error_handler. When error...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
