Hello Nordic community,
I’m working on a project with the nRF52840 DK (PCA10056) using the nRF5 SDK and the S140 SoftDevice. My goal is to:
1. Read two NTC thermistors...
I am trying to write SPI code for the nRF52840 dongle. Since the nRF5 SDK does not directly provide an example for the dongle, I followed the steps defined in this tutorial...
I am trying to build using a custom board and 2.9.1, but am getting these errors:
My dts looks like this:
I have the width specified. Much of this is over...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
Hi Nordic Team,
Previously, with the nRF52840, we could use the internal ADC channel to directly measure the supply voltage (VCC) for battery monitoring without external...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hello,
I am working with the NRF5340dk, nrf7002ek, and PPKII. I am unable to get the DK to power up with the PPK. I used a knife to break the trace but for some reason...
I want to add an external PA to the NRF51422. My understanding of 15.247 is that you can transmit up to 30dBm if you use spread spectrum. Does the NRF51422 use DSSS for Bluetooth...
When is the most appropriate time to set the transmit power while using the S120 softdevice? I want to set it once at power up. Most examples that use the S110 SD set the...
Suppose I want my BT peripheral to provide Measured value of sensor X and Location of sensor.
Currently I have to send the following attributes
Service Attrinbute
Characteristic...
Hi All,
I am working a custom board for 51822. We have wired the UART RX/TX pins to a microusb connector (No RXD/TXD pins wired). The problem is once we connect it to PC...
Hello,
all was working fine, until today.
When I plug my dongle, my computer does not react.
The green light on the dongle is off.
Even if I suppose that it's a...
For my current project, I need to compile the »over the air bootloader« with gcc (because our buildserver runs on linux, developers using Mac … no Windows and no Keil so far...
Hello, I want to get Pwm output using softdevice but i am not getting it.Here is my code attached main.c please tell me where i am going wrong.Do ineed to initialize softdevice...
I am looking at using the nRF51822 in an application to create an Ethernet gateway and want to be able to download new firmware to the nRF51822 from a remote server. I plan...
I have an nRF51822 application using the Soft Device 110. I want to perform bonding with a central without MITM protection. In my on_ble_evt() event handler, when the event...
Hi,
I am new to the scene of BLE beacon development. I am using multiple Bluetooth smart beacon kits for indoor ranging/positioning purposes. To reduce the effect of interference...
Hi,
For S110 6.0.0 we use such script to split hex to binary. But it seems 7.0.0 is changed and current way is not working anymore.
Convert from hex to binary. Split...
Hi
I am writing my own bonding manager.
In the S110 stack after Phase 3 of pairing the keys are exchanged which result in the EVT_AUTH_STATUS event which in turn contains...
when I add my own service and add characteristic, a odd phenomenon confuse me.
When I set cccd_md.write_perm:
BLE_GAP_CONN_SEC_MODE_SET_OPEN(&cccd_md.write_perm);
...
after several attempts to debug and understand what goes in my handlers in the BLE callbacks, I thought to give a UART logger a try.
this is what I'm trying to use: OpenLog...
